Differences

This shows you the differences between two versions of the page.

--- aruba_networks:switch:2930f:recovery_password [2024/10/05 01:03] – aperez
+++ aruba_networks:switch:2930f:recovery_password [2025/07/17 17:33] (current) – [Factory default] aperez
@@ Line 106: / Line 106: @@
 Default password recovery user: Enabled
-Management User Table
+  Management User Table
+  ---------------------
+  USER    PASSWD  ROLE   STATUS
+  ----    ------  ----   ------
+  admin   *****   root   ACTIVE
+  The following is an example of the show mgmt-user command when the alternate password recovery user is configured.
+  (host) #**show mgmt-user**
+  Default password recovery user: Disabled
+  Management User Table
+  ---------------------
+  USER       PASSWD  ROLE    STATUS
+  ----       ------  ----    ------
+  admin      *****   root    ACTIVE
+  recadmin   *****   passR   ACTIVE
----------------------
+----
+----
-USER    PASSWD  ROLE   STATUS
+====== Using Clear/Reset ======
-----    ------  ----   ------
+**Procedure**
-admin   *****   root   ACTIVE
+  - Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
+  - Continue to press the Clear button while releasing the Reset button.
+  - When the Self Test LED begins to flash, release the Clear button.
-The following is an example of the show mgmt-user command when the alternate password recovery user is configured.
+The switch then completes its self test and begins operating with the configuration restored to the factory default settings.
-(host) #**show mgmt-user**
+**Restoring the Factory Default Configuration**
-Default password recovery user: Disabled
+You can also use the Reset button together with the Clear button (Reset+Clear) to restore the factory default configuration for the switch. To do this:
-Management User Table
+.  Press and hold the Reset button.
----------------------
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
-USER       PASSWD  ROLE    STATUS
+.  While holding the Reset button, press and hold the Clear button.
-----       ------  ----    ------
+{{ :aruba_networks:switch:2930f:figure_2-14_272x142.png?200 |}}
-admin      *****   root    ACTIVE
+.  Release the Reset button.
-recadmin   *****   passR   ACTIVE
+{{ :aruba_networks:switch:2930f:figure_2-15_363x142.png?200 |}}
+.  When the Test LED to the right of the Clear button begins flashing, release the Clear button.
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
+. It takes approximately 20-25 seconds for the switch to reboot. This process restores the switch configuration to the factory default settings.
+----
+----
+====== Aruba 3810M Switch Series - LED Indicators ======
+Switch and port LEDs on front of the switches
+Front of Switch Status and Mode LED Behavior describes the switch chassis and Flex Port status LEDs and also the Switch Mode LEDs.
+Below table describes the switch Port LEDs and their different mode behaviors.
+{{ :aruba_networks:switch:2930f:3810m.jpg?600 |}}
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | PoE LED |
+| 5 | Usr LED |
+| 6 | Reset button |
+| 7 | Clear button |
+| 8 | Back Module status LED |
+| 9 | Aux Port status LED |
+| 10 | Unit Identification LED |
+| 11 | Global status LED |
+===== Switch and port LEDs for JL075A =====
+{{ :aruba_networks:switch:2930f:3810m-2.jpg?600 |}}
+Switch and Port LEDs Label and Description for **JL075A**
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | Usr LED |
+| 5 | Reset button |
+| 6 | Clear button |
+| 7 | Back Module status LED |
+| 8 | Aux Port status LED |
+| 9 | Unit Identification LED |
+| 10 | Global status LED |
+**[[https://support.hpe.com/hpesc/public/docDisplay?docId=sf000094063en_us&docLocale=en_US|Aruba 3810M Switch Series - LED Indicators]]**
+----
+----
+===== ROM information: =====
+Enter h or ? for help.
+=>**h**
+=>**erase-all**
+The system will boot to the last-booted software image and all management
+module files except software images will be erased.  Continue (y/n)? **y**
+**Booting Primary Software Image...**
+Aruba-Stack-3810M#
+----
+----
 ====== Access Security guide ======
@@ Line 161: / Line 251: @@
 {{ :aruba_networks:switch:2930f:configuration:access_security_guide_2930f.pdf |Access Security Guide 2930F}}
 {{pdfjs 46em >:aruba_networks:switch:2930f:configuration:access_security_guide_2930f.pdf }}
+----
+----
+====== Factory default ======
+  erase startup-config
+  Erase startup-config [y/n]? y
+  reload
+----
+----