Differences

This shows you the differences between two versions of the page.

--- aruba_networks:switch:2930f:recovery_password [2024/10/05 01:05] – aperez
+++ aruba_networks:switch:2930f:recovery_password [2024/10/05 01:28] (current) – aperez
@@ Line 106: / Line 106: @@
 Default password recovery user: Enabled
-Management User Table
+  Management User Table
   ---------------------
@@ Line 131: / Line 131: @@
   admin      *****   root    ACTIVE
   recadmin   *****   passR   ACTIVE
+----
+----
+====== Using Clear/Reset ======
+**Procedure**
+  - Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
+  - Continue to press the Clear button while releasing the Reset button.
+  - When the Self Test LED begins to flash, release the Clear button.
+The switch then completes its self test and begins operating with the configuration restored to the factory default settings.
+**Restoring the Factory Default Configuration**
+You can also use the Reset button together with the Clear button (Reset+Clear) to restore the factory default configuration for the switch. To do this:
+.  Press and hold the Reset button.
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
+.  While holding the Reset button, press and hold the Clear button.
+{{ :aruba_networks:switch:2930f:figure_2-14_272x142.png?200 |}}
+.  Release the Reset button.
+{{ :aruba_networks:switch:2930f:figure_2-15_363x142.png?200 |}}
+.  When the Test LED to the right of the Clear button begins flashing, release the Clear button.
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
+. It takes approximately 20-25 seconds for the switch to reboot. This process restores the switch configuration to the factory default settings.
+----
+----
+====== Aruba 3810M Switch Series - LED Indicators ======
+Switch and port LEDs on front of the switches
+Front of Switch Status and Mode LED Behavior describes the switch chassis and Flex Port status LEDs and also the Switch Mode LEDs.
+Below table describes the switch Port LEDs and their different mode behaviors.
+{{ :aruba_networks:switch:2930f:3810m.jpg?600 |}}
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | PoE LED |
+| 5 | Usr LED |
+| 6 | Reset button |
+| 7 | Clear button |
+| 8 | Back Module status LED |
+| 9 | Aux Port status LED |
+| 10 | Unit Identification LED |
+| 11 | Global status LED |
+===== Switch and port LEDs for JL075A =====
+{{ :aruba_networks:switch:2930f:3810m-2.jpg?600 |}}
+Switch and Port LEDs Label and Description for **JL075A**
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | Usr LED |
+| 5 | Reset button |
+| 6 | Clear button |
+| 7 | Back Module status LED |
+| 8 | Aux Port status LED |
+| 9 | Unit Identification LED |
+| 10 | Global status LED |
+**[[https://support.hpe.com/hpesc/public/docDisplay?docId=sf000094063en_us&docLocale=en_US|Aruba 3810M Switch Series - LED Indicators]]**
+----
+----
+===== ROM information: =====
+Enter h or ? for help.
+=>**h**
+=>**erase-all**
+The system will boot to the last-booted software image and all management
+module files except software images will be erased.  Continue (y/n)? **y**
+**Booting Primary Software Image...**
+Aruba-Stack-3810M#
+----
+----
 ====== Access Security guide ======