Differences

This shows you the differences between two versions of the page.

--- aruba_networks:switch:2930f:recovery_password [2024/10/05 01:13] – aperez
+++ aruba_networks:switch:2930f:recovery_password [2025/07/17 17:33] (current) – [Factory default] aperez
@@ Line 153: / Line 153: @@
 .  Press and hold the Reset button.
-{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?400 |}}
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
 .  While holding the Reset button, press and hold the Clear button.
-{{ :aruba_networks:switch:2930f:figure_2-14_272x142.png?400 |}}
+{{ :aruba_networks:switch:2930f:figure_2-14_272x142.png?200 |}}
 .  Release the Reset button.
-{{ :aruba_networks:switch:2930f:figure_2-15_363x142.png?400 |}}
+{{ :aruba_networks:switch:2930f:figure_2-15_363x142.png?200 |}}
 .  When the Test LED to the right of the Clear button begins flashing, release the Clear button.
-{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?400 |}}
+{{ :aruba_networks:switch:2930f:figure_2-13_272x144.png?200 |}}
 . It takes approximately 20-25 seconds for the switch to reboot. This process restores the switch configuration to the factory default settings.
@@ Line 180: / Line 180: @@
 Below table describes the switch Port LEDs and their different mode behaviors.
-{{ :aruba_networks:switch:2930f:3810m.jpg?400 |}}
+{{ :aruba_networks:switch:2930f:3810m.jpg?600 |}}
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | PoE LED |
+| 5 | Usr LED |
+| 6 | Reset button |
+| 7 | Clear button |
+| 8 | Back Module status LED |
+| 9 | Aux Port status LED |
+| 10 | Unit Identification LED |
+| 11 | Global status LED |
+===== Switch and port LEDs for JL075A =====
+{{ :aruba_networks:switch:2930f:3810m-2.jpg?600 |}}
+Switch and Port LEDs Label and Description for **JL075A**
+^ Label ^ Description ^
+| 1 | Switch Port LEDs |
+| 2 | LED Mode button |
+| 3 | Speed LED |
+| 4 | Usr LED |
+| 5 | Reset button |
+| 6 | Clear button |
+| 7 | Back Module status LED |
+| 8 | Aux Port status LED |
+| 9 | Unit Identification LED |
+| 10 | Global status LED |
+**[[https://support.hpe.com/hpesc/public/docDisplay?docId=sf000094063en_us&docLocale=en_US|Aruba 3810M Switch Series - LED Indicators]]**
+----
+----
+===== ROM information: =====
+Enter h or ? for help.
+=>**h**
+=>**erase-all**
+The system will boot to the last-booted software image and all management
+module files except software images will be erased.  Continue (y/n)? **y**
+**Booting Primary Software Image...**
+Aruba-Stack-3810M#
 ----
@@ Line 204: / Line 251: @@
 {{ :aruba_networks:switch:2930f:configuration:access_security_guide_2930f.pdf |Access Security Guide 2930F}}
 {{pdfjs 46em >:aruba_networks:switch:2930f:configuration:access_security_guide_2930f.pdf }}
+----
+----
+====== Factory default ======
+  erase startup-config
+  Erase startup-config [y/n]? y
+  reload
+----
+----