User Tools

Site Tools


aruba_networks:switch:6400:6400_configuration_example_script

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
aruba_networks:switch:6400:6400_configuration_example_script [2025/02/19 16:19] – [6300 Switch LAG errror: State information : Disabled by aggregation] aperezaruba_networks:switch:6400:6400_configuration_example_script [2025/05/09 09:41] (current) aperez
Line 1803: Line 1803:
   * **65.535** – reserved.   * **65.535** – reserved.
  
-**Switch A - 6400:** 
  
 +**OSPF**
  
-  router ospf 1 +**[[https://arubanetworking.hpe.com/techdocs/AOS-CX/10.15/HTML/ip_route_6300-6400-8100-83xx-9300-10000/Content/Chp_OSPFv2/OSPFv2_cmds/red-osp-10.htm|Redistribute (ospf)]]**
-    router-id 172.22.0.+
-    redistribute bgp +
-    area 0.0.0.0+
  
-  router bgp 65010 
-    bgp router-id 172.22.0.1 
-    neighbor 172.18.0.4 remote-as 65020 
-    address-family ipv4 unicast 
-        neighbor 172.18.0.4 default-originate 
-        neighbor 172.18.0.4 activate 
-        network 172.18.0.0/27 
-    exit-address-family 
  
-  interface vlan 1 + 
-  ip ospf 1 area 0.0.0.0 +---- 
-  ip ospf network point-to-point+ 
 +{{ :aruba_networks:switch:6400:ospf_final.png?600 |}} 
 + 
 + 
 +---- 
 + 
 +================ 
 +**SIDE-A 6400-A** 
 +================ 
 + 
 +  Example set vlan L2 to both SW 6400 A and B:
      
-  interface vlan 500 +  vlan 508 
-  ip ospf 1 area 0.0.0.0 +      name ST 
-  ip ospf network point-to-point+      vsx-sync 
 +      ip igmp snooping enable 
 +      ip igmp snooping version 2 
 +      ip igmp snooping apply access-list mygroup1 
 + 
 + 
 +  vsx 
 +      system-mac 02:01:00:00:01:00 
 +      inter-switch-link lag 256 
 +      role primary 
 +      keepalive peer 192.168.100.2 source 192.168.100.1 vrf keepAlive 
 +      vsx-sync aaa acl-log-timer bfd-global bgp copp-policy dhcp-relay dhcp-server dns icmp-tcp lldp loop-protect-  
 +  global mac-lockout mclag-interfaces ospf qos-global route-map sflow-global snmp ssh stp-global time vsx-global
      
-  interface vlan 501 +  ip route 0.0.0.0/0 172.16.32.4
-  ip ospf 1 area 0.0.0.0 +
-  ip ospf network point-to-point+
      
-  interface vlan 505 +  router ospf 1 
-  ip ospf 1 area 0.0.0.0 +      router-id 172.22.0.1 
-  ip ospf network point-to-point+      max-metric router-lsa on-startup 
 +      passive-interface default 
 +      graceful-restart restart-interval 300 
 +      trap-enable 
 +      area 0.0.0.0
      
-  interface vlan 506 +  interface loopback 0 
-  ip ospf 1 area 0.0.0.0 +      ip address 172.22.0.1/32 
-  ip ospf network point-to-point+      ip ospf 1 area 0.0.0.0
      
-  interface vlan 507 +  vlan 531 
-  ip ospf 1 area 0.0.0.0 +      name NORTH-OSPF 
-  ip ospf network point-to-point+      vsx-sync 
 +      description TRANSIT VLAN
      
   interface vlan 508   interface vlan 508
-  ip ospf 1 area 0.0.0.0 +      description Vlan 508 ST 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.28.72.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.28.72.1 
 +      ip helper-address 10.28.64.22 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 509 +  interface vlan 514 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 514 AC 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 172.16.40.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 172.16.40.1 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 510 +  interface vlan 530 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 530 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.28.216.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.28.216.1 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 511 +  interface vlan 531 
-  ip ospf 1 area 0.0.0.0 +      description TRANSIT VLAN 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.5/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 50 
 +      ip ospf network point-to-point
      
-  interface vlan 512 +  interface vlan 1019 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 1019 PtP 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.1/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 10 
 +      ip ospf network point-to-point 
 + 
 + 
 +================ 
 +**SIDE-A 6400-B** 
 +================ 
 + 
 +  vsx 
 +      system-mac 02:01:00:00:01:00 
 +      inter-switch-link lag 256 
 +      role secondary 
 +      keepalive peer 192.168.100.1 source 192.168.100.2 vrf keepAlive 
 +      vsx-sync aaa acl-log-timer bfd-global bgp copp-policy dhcp-relay dhcp-server dns icmp-tcp lldp loop-protect-  
 +  global mac-lockout mclag-interfaces ospf qos-global route-map sflow-global snmp ssh stp-global time vsx-global
      
-  interface vlan 513 +  ip route 0.0.0.0/0 172.16.32.4 
-  ip ospf 1 area 0.0.0.0 +    
-  ip ospf network point-to-point+   router ospf 1 
 +      router-id 172.22.0.2 
 +      max-metric router-lsa on-startup 
 +      passive-interface default 
 +      graceful-restart restart-interval 300 
 +      trap-enable 
 +      area 0.0.0.0 
 +   
 +  interface loopback 0 
 +      ip address 172.22.0.2/32 
 +      ip ospf 1 area 0.0.0.0 
 +   
 +  vlan 531 
 +      name NORTH-OSPF 
 +      vsx-sync 
 +      description TRANSIT VLAN 
 +   
 +  interface vlan 508 
 +      description Vlan 508 ST 
 +      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.28.72.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.28.72.1 
 +      ip helper-address 10.28.64.22 
 +      ip ospf 1 area 0.0.0.0
      
   interface vlan 514   interface vlan 514
-  ip ospf 1 area 0.0.0.0 +      description Vlan 514 AC 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 172.16.40.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 172.16.40.1 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 515 +  interface vlan 530 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 530 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.28.216.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.28.216.1 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 516 +  interface vlan 531 
-  ip ospf 1 area 0.0.0.0 +      description TRANSIT VLAN 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.6/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 50 
 +      ip ospf network point-to-point
      
-  interface vlan 517 +  interface vlan 1019 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 1019 PtP 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.14/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 10 
 + 
 +================ 
 +**SIDE-B 6400-A** 
 +================ 
 + 
 +  Example set vlan L2 to both SW 6400 A and B: 
 +    
 +  vlan 708 
 +      name ST                                                              
 +      vsx-sync 
 +      ip igmp snooping enable 
 +      ip igmp snooping version 2 
 +      ip igmp snooping apply access-list mygroup1 
 + 
 + 
 +  vsx 
 +      system-mac 02:01:00:00:02:00 
 +      inter-switch-link lag 256 
 +      role primary 
 +      keepalive peer 192.168.102.2 source 192.168.102.1 vrf keepAlive 
 +      vsx-sync aaa acl-log-timer bfd-global bgp copp-policy dhcp-relay dhcp-server dns icmp-tcp lldp loop-protect-  
 +  global mac-lockout mclag-interfaces ospf qos-global route-map sflow-global snmp ssh stp-global time vsx-global
      
-  interface vlan 518 +  ip route 0.0.0.0/0 172.20.32.4
-  ip ospf 1 area 0.0.0.0 +
-  ip ospf network point-to-point+
      
-  interface vlan 519 +  router ospf 1 
-  ip ospf 1 area 0.0.0.0 +      router-id 172.22.0.3 
-  ip ospf network point-to-point+      max-metric router-lsa on-startup 
 +      passive-interface default 
 +      graceful-restart restart-interval 300 
 +      trap-enable 
 +      area 0.0.0.0
      
-  interface vlan 520 +  vlan 731 
-  ip ospf 1 area 0.0.0.0 +      name SOUTH-OSPF 
-  ip ospf network point-to-point+      vsx-sync 
 +      description TRANSIT VLAN
      
-  interface vlan 521 +  interface loopback 0 
-  ip ospf 1 area 0.0.0.0 +      ip address 172.22.0.3/32 
-  ip ospf network point-to-point+      ip ospf 1 area 0.0.0.0
      
-  interface vlan 522 +  interface vlan 708 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 708 ST 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.56.72.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.56.72.1 
 +      ip helper-address 10.56.64.22 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 523 +  interface vlan 714 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 714 AC 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 172.20.40.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 172.20.40.1 
 +      ip helper-address 10.56.64.22 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 524 +  interface vlan 730 
-  ip ospf 1 area 0.0.0.0 +      description VLAN 730 9K 
-  ip ospf network point-to-point+      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.56.216.2/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.56.216.1 
 +      ip ospf 1 area 0.0.0.0
      
-  interface vlan 525 +  interface vlan 731 
-  ip ospf 1 area 0.0.0.0 +      description TRANSIT VLAN 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.9/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 50 
 +      ip ospf network point-to-point
      
-  interface vlan 526 +  interface vlan 1019 
-  ip ospf 1 area 0.0.0.0 +      description Vlan 1019 PtP 
-  ip ospf network point-to-point+      vsx active-forwarding 
 +      ip address 172.18.0.2/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 10 
 +      ip ospf network point-to-point
      
-  interface vlan 527 +================ 
-  ip ospf area 0.0.0.0 +**SIDE-B 6400-B** 
-  ip ospf network point-to-point+================ 
 + 
 + 
 +  vsx 
 +      system-mac 02:01:00:00:02:00 
 +      inter-switch-link lag 256 
 +      role secondary 
 +      keepalive peer 192.168.102.source 192.168.102.2 vrf keepAlive 
 +      vsx-sync aaa acl-log-timer bfd-global bgp copp-policy dhcp-relay dhcp-server dns icmp-tcp lldp loop-protect-  
 +  global mac-lockout mclag-interfaces ospf qos-global route-map sflow-global snmp ssh stp-global time vsx-global
      
-  interface vlan 530 +  ip route 0.0.0.0/0 172.20.32.4 
-  ip ospf 1 area 0.0.0.0 +   
-  ip ospf network point-to-point+  vlan 731 
 +      name SOUTH-OSPF 
 +      vsx-sync 
 +      description TRANSIT VLAN 
 +     
 +  router ospf 1 
 +      router-id 172.22.0.4 
 +      max-metric router-lsa on-startup 
 +      passive-interface default 
 +      graceful-restart restart-interval 300 
 +      trap-enable 
 +      area 0.0.0.0 
 +   
 +  interface loopback 0 
 +      ip address 172.22.0.4/32 
 +      ip ospf 1 area 0.0.0.0 
 +   
 +  interface vlan 708 
 +      description Vlan 708 ST 
 +      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.56.72.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.56.72.1 
 +      ip helper-address 10.56.64.22 
 +      ip ospf 1 area 0.0.0.0 
 +    
 +  interface vlan 714 
 +      description Vlan 714 AC 
 +      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 172.20.40.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 172.20.40.1 
 +      ip helper-address 10.56.64.22 
 +      ip ospf 1 area 0.0.0.0 
 +   
 +  interface vlan 730 
 +      description VLAN 730 9K 
 +      vsx-sync active-gateways 
 +      ip mtu 9100 
 +      ip address 10.56.216.3/23 
 +      active-gateway ip mac 12:01:00:00:01:00 
 +      active-gateway ip 10.56.216.1 
 +      ip ospf 1 area 0.0.0.0 
 +   
 +  interface vlan 731 
 +      description TRANSIT VLAN 
 +      vsx active-forwarding 
 +      ip address 172.18.0.10/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 50 
 +      ip ospf network point-to-point 
 +   
 +  interface vlan 1019 
 +      description Vlan 1019 PtP 
 +      vsx active-forwarding 
 +      ip address 172.18.0.13/30 
 +      ip ospf 1 area 0.0.0.0 
 +      no ip ospf passive 
 +      ip ospf cost 10 
 +      ip ospf network point-to-point
  
  
-**SwitchA(config)# show ip ospf neighbors**+---- 
 +----
  
-**SwitchB# show lldp neighbor**+**OSPF Troubleshooting**
  
-  SwitchA# show ip ospf neighbors + 
-  VRF default                          Process 1 +**{{ :aruba_networks:switch:6400:15be0a8e-5922-47b6-ae26-a7218295f7e8.pdf |OSPF Troubleshooting}}** 
-  ===================================================+ 
 +{{pdfjs 46em >:aruba_networks:switch:6400:15be0a8e-5922-47b6-ae26-a7218295f7e8.pdf }} 
 + 
 + 
 + 
 +{{ youtube>N9dIGVzdjIU }} 
 + 
 + 
 + 
 +---- 
 +---- 
 + 
 +**FEC** on an SFP port refers to **Forward Error Correction (FEC)**, which is a technique used in fiber optic and Ethernet networks to enhance data transmission reliability by detecting and correcting errors without the need for retransmission. 
 +  
 +**FEC (Forward Error Correction)**: 
 +FEC is a mechanism that adds redundant information to the transmitted data. This redundancy allows the receiving end to detect and correct errors caused by signal degradation or noise during transmission. 
 + 
 +Purpose: FEC is essential for high-speed data links (e.g., 10G, 25G, 40G, 100G Ethernet) to improve link quality and performance. 
 + 
 +Types: Different FEC modes can be used depending on the standard and speed of the connection (e.g., Reed-Solomon FEC). 
 + 
 + 
 +  *   **auto**   Enable FEC Auto-Neg 
 +  *   **cl108**  Enable clause108 with 25G 
 +  *   **cl74**   Enable clause74 with 25G 
 +  *   **off**    Turn FEC off, FEC is mandatory for speeds 50G or higher 
 + 
 + 
 +---- 
 +---- 
 + 
 + 
 +**Benefits of FEC on SFP Ports**: 
 + 
 +  * Error Correction: FEC can correct errors due to signal attenuation or interference. 
 +  * Better Link Performance: Allows for longer cable runs or higher speeds by improving signal integrity. 
 +  * No Retransmissions: Unlike other error correction methods, FEC works proactively without needing retransmissions, which is important for low-latency environments. 
 + 
 +---- 
 + 
 +**Aruba Switch 6400:** 
 + 
 + 
 +  CS-2P-MDFHA-A#** show ver** 
 +  ----------------------------------------------------------------------------- 
 +  ArubaOS-CX 
 +  (c) Copyright 2017-2024 Hewlett Packard Enterprise Development LP 
 +  ----------------------------------------------------------------------------- 
 +  Version      FL.10.13.1010 
 +  Build Date   2024-04-09 00:34:12 UTC 
 +  Build ID     : ArubaOS-CX:FL.10.13.1010:ef2109377880:202404090010 
 +  Build SHA    : ef21093778805e954ec130b0939d34927bb7ba19 
 +  Hot Patches 
 +  Active Image : primary
      
-  Total Number of Neighbors 26+  Service OS Version FL.01.14.0002 
 +  BIOS Version       : FL.01.0002 
 + 
 +CS-2P-MDFHA-A(config)# **interface 1/3/36** 
 + 
 +**error-control**    Configure the error control (**FEC**) mode 
 + 
 +  CS-2P-MDFHA-A(config-if)# error-control 
 +    auto        Use the transceiver default 
 +    base-r-fec  Use IEEE BASE-R (Firecode) FEC 
 +    none        Do not use any FEC 
 +    rs-fec      Use IEEE Reed-Solomon FEC 
 + 
 +---- 
 +---- 
 +====== boot system ====== 
 + 
 +**Rebooting the system from the configured default operating system image**: 
 + 
 +  switch# boot system 
 +  Do you want to save the current configuration (y/n)? y 
 +  The running configuration was saved to the startup configuration.
      
-  Neighbor ID      Priority  State             Nbr Address       Interface +  This will reboot the entire switch and render it unavailable 
-  ------------------------------------------------------------------------- +  until the process is complete. 
-  192.168.2.3      n/a       FULL              172.16.28.3        vlan1+  Continue (y/n)? y 
 +  The system is going down for reboot. 
 +  The system is going down for reboot. 
 + 
 +**Rebooting the system from the secondary operating system image, setting the secondary operating system image as the configured default boot image:** 
 + 
 +  switch# boot system secondary 
 +  Default boot image set to secondary. 
 +   
 +  Do you want to save the current configuration (y/n)? n 
 +   
 +  This will reboot the entire switch and render it unavailable 
 +  until the process is complete. 
 +  Continue (y/n)? y 
 +  The system is going down for reboot. 
 +   
 +  Canceling a system reboot:
      
-  192.168.2.3      n/a       FULL              10.28.64.3         vlan500+  switch# boot system
      
-  192.168.2.3      n/a       FULL              192.168.2.3        vlan501+  Do you want to save the current configuration (y/n)? n
      
-  192.168.2.3      n/a       FULL              172.16.32.3        vlan505+  This will reboot the entire switch and render it unavailable 
 +  until the process is complete. 
 +  Continue (y/n)? n 
 +  Reboot aborted. 
 +  switch#
      
-  192.168.2.3      n/a       FULL              172.16.36.3        vlan506 
  
 ---- ----
 ---- ----
  
 +====== Steps to get the support files for both the switches: ======
  
  
 +**For SFTP**: 
 +  Switch# copy support-files all sftp:// user@Address of Local Server>/support-files.tar.gz vrf default 
 +**For TFTP**: 
 +  Switch# copy support-files all tftp:// Address of Local Server>/support-files.tar.gz vrf default 
  
  
 +  CS-2C-MDFHA-A# copy support-files all tftp://10.56.64.22/support-files.tar.gz vrf default
 +  The operation to copy all support files could take a while to complete.
 +  
 +  Do you want to continue (y/n)? y
 +  Collection in progress...
 +  Standby management module is not reachable
 +  Unable to gather information from the standby management module
 +  
 +  
 +  show tech output collection is in progress...
 +  Done
 +  
 +  Done
 +  Attempting to copy...
 +    % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
 +                                   Dload  Upload   Total   Spent    Left  Speed
 +   65 69.8M    0       65 45.6M      0   467k  0:02:32  0:01:40  0:00:52  648k
  
  
Line 1965: Line 2301:
  
  
 +Please note on both the above cases you can use the specific VRF (ex, here we have used management VRF), if you do not specify a VRF, then it will take the default VRF 
  
 +OR 
  
 +Copy the support files to USB and then upload manually. 
  
 +**For USB**: 
 +For USB option, First you need to enable the USB and then you need to Mount, To do so 
 +  Switch#(config) usb mount 
 +Verification can be done by 
 +  Switch# show usb 
 +  enabled: yes 
 +  mounted: yes 
 +  Switch# copy support-files all usb://support-files.tar.gz 
 +After copied use this command to unmount the usb 
 +  Switch#(config) usb unmount 
 + USB should be formatted with FAT32 option before inserting to switch. 
 +
 +----
 +----
 +
 +====== Images ======
 +
 +
 +  CS-2P-MDFHA-B(config-if-vlan)# show images
 +  ---------------------------------------------------------------------------
 +  ArubaOS-CX Primary Image
 +  ---------------------------------------------------------------------------
 +  Version : FL.10.13.1010
 +  Size    : 998 MB
 +  Date    : 2024-04-09 00:34:12 UTC
 +  SHA-256 : 53bbd1354dd22bffa2df52b22fe8f2dd5cc05a10bcd9ae8c9e01fc93c830d0ec
 +  
 +  ---------------------------------------------------------------------------
 +  ArubaOS-CX Secondary Image
 +  ---------------------------------------------------------------------------
 +  Version : FL.10.09.1050
 +  Size    : 872 MB
 +  Date    : 2022-09-13 23:40:16 UTC
 +  SHA-256 : 631640f32e58f3719f56b36474d02c98666a519fb7775d3b263a36783eaafcfd
 +  
 +  Default Image : primary
 +  Boot Profile Timeout : 5 seconds
 +  
 +  ------------------------------------------------------
 +  Management Module 1/1 (Active)
 +  ------------------------------------------------------
 +  Active Image       : primary
 +  Service OS Version : FL.01.14.0002
 +  BIOS Version       : FL.01.0002
 +  
 +  CS-2P-MDFHA-A# boot system primary
 +  Default boot image set to primary.
 +  Checking if the configuration needs to be saved...
 +  
 +  Do you want to save the current configuration (y/n)? y
 +  The running configuration was saved to the startup configuration.
 +  
 +  Checking for updates needed to programmable devices...
 +  Done checking for updates.
 +  
 +  2 non-failsafe device(s) also need to be updated.
 +  Please run the 'allow-unsafe-updates' command to enable these updates.
 +     
 +  This will reboot the entire switch and render it unavailable
 +  until the process is complete.
 +  Continue (y/n)?
 +
 +----
 +----
aruba_networks/switch/6400/6400_configuration_example_script.1739999956.txt.gz · Last modified: 2025/02/19 16:19 by aperez

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki