Differences

This shows you the differences between two versions of the page.

--- aruba_networks:switch:6400:6400_configuration_example_script [2025/03/07 11:21] – [6300 Switch LAG errror: State information : Disabled by aggregation] aperez
+++ aruba_networks:switch:6400:6400_configuration_example_script [2025/04/20 12:07] (current) – [Steps to get the support files for both the switches:] aperez
@@ Line 1802: / Line 1802: @@
   * **64.512 – 65.534** – private AS numbers.
   * **65.535** – reserved.
+**[[https://arubanetworking.hpe.com/techdocs/AOS-CX/10.15/HTML/ip_route_6300-6400-8100-83xx-9300-10000/Content/Chp_OSPFv2/OSPFv2_cmds/red-osp-10.htm|Redistribute (ospf)]]**
 **Switch A - 6400:**
@@ Line 2103: / Line 2106: @@
 {{pdfjs 46em >:aruba_networks:switch:6400:15be0a8e-5922-47b6-ae26-a7218295f7e8.pdf }}
-**[[https://arubanetworking.hpe.com/techdocs/AOS-CX/10.15/HTML/ip_route_6300-6400-8100-83xx-9300-10000/Content/Chp_OSPFv2/OSPFv2_cmds/red-osp-10.htm|redistribute (ospf)]]**
 {{ youtube>N9dIGVzdjIU }}
@@ Line 2166: / Line 2170: @@
     none        Do not use any FEC
     rs-fec      Use IEEE Reed-Solomon FEC
+----
+----
+====== boot system ======
+**Rebooting the system from the configured default operating system image**:
+  switch# boot system
+  Do you want to save the current configuration (y/n)? y
+  The running configuration was saved to the startup configuration.
+  This will reboot the entire switch and render it unavailable
+  until the process is complete.
+  Continue (y/n)? y
+  The system is going down for reboot.
+  The system is going down for reboot.
+**Rebooting the system from the secondary operating system image, setting the secondary operating system image as the configured default boot image:**
+  switch# boot system secondary
+  Default boot image set to secondary.
+  Do you want to save the current configuration (y/n)? n
+  This will reboot the entire switch and render it unavailable
+  until the process is complete.
+  Continue (y/n)? y
+  The system is going down for reboot.
+  Canceling a system reboot:
+  switch# boot system
+  Do you want to save the current configuration (y/n)? n
+  This will reboot the entire switch and render it unavailable
+  until the process is complete.
+  Continue (y/n)? n
+  Reboot aborted.
+  switch#
+----
+----
+====== Steps to get the support files for both the switches: ======
+**For SFTP**:
+  Switch# copy support-files all sftp:// user@Address of Local Server>/support-files.tar.gz vrf default
+**For TFTP**:
+  Switch# copy support-files all tftp:// Address of Local Server>/support-files.tar.gz vrf default
+  CS-2C-MDFHA-A# copy support-files all tftp://10.56.64.22/support-files.tar.gz vrf default
+  The operation to copy all support files could take a while to complete.
+  Do you want to continue (y/n)? y
+  Collection in progress...
+  Standby management module is not reachable
+  Unable to gather information from the standby management module
+  show tech output collection is in progress...
+  Done
+  Done
+  Attempting to copy...
+    % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
+                                   Dload  Upload   Total   Spent    Left  Speed
+69.8M    0     0   65 45.6M      0   467k  0:02:32  0:01:40  0:00:52  648k
+Please note on both the above cases you can use the specific VRF (ex, here we have used management VRF), if you do not specify a VRF, then it will take the default VRF
+OR
+Copy the support files to USB and then upload manually.
+**For USB**:
+For USB option, First you need to enable the USB and then you need to Mount, To do so
+  Switch#(config) usb mount
+Verification can be done by
+  Switch# show usb
+  enabled: yes
+  mounted: yes
+  Switch# copy support-files all usb://support-files.tar.gz
+After copied use this command to unmount the usb
+  Switch#(config) usb unmount
+ USB should be formatted with FAT32 option before inserting to switch.
+----
+----
+====== Images ======
+  CS-2P-MDFHA-B(config-if-vlan)# show images
+  ---------------------------------------------------------------------------
+  ArubaOS-CX Primary Image
+  ---------------------------------------------------------------------------
+  Version : FL.10.13.1010
+  Size    : 998 MB
+  Date    : 2024-04-09 00:34:12 UTC
+  SHA-256 : 53bbd1354dd22bffa2df52b22fe8f2dd5cc05a10bcd9ae8c9e01fc93c830d0ec
+  ---------------------------------------------------------------------------
+  ArubaOS-CX Secondary Image
+  ---------------------------------------------------------------------------
+  Version : FL.10.09.1050
+  Size    : 872 MB
+  Date    : 2022-09-13 23:40:16 UTC
+  SHA-256 : 631640f32e58f3719f56b36474d02c98666a519fb7775d3b263a36783eaafcfd
+  Default Image : primary
+  Boot Profile Timeout : 5 seconds
+  ------------------------------------------------------
+  Management Module 1/1 (Active)
+  ------------------------------------------------------
+  Active Image       : primary
+  Service OS Version : FL.01.14.0002
+  BIOS Version       : FL.01.0002
+  CS-2P-MDFHA-A# boot system primary
+  Default boot image set to primary.
+  Checking if the configuration needs to be saved...
+  Do you want to save the current configuration (y/n)? y
+  The running configuration was saved to the startup configuration.
+  Checking for updates needed to programmable devices...
+  Done checking for updates.
+non-failsafe device(s) also need to be updated.
+  Please run the 'allow-unsafe-updates' command to enable these updates.
+  This will reboot the entire switch and render it unavailable
+  until the process is complete.
+  Continue (y/n)?
 ----
 ----