Differences

This shows you the differences between two versions of the page.

--- ruijie:switch:general_configuration_switch_l2 [2020/09/22 20:29] – aperez
+++ ruijie:switch:general_configuration_switch_l2 [2020/09/22 20:41] (current) – aperez
@@ Line 1737: / Line 1737: @@
 !
 ----
-**interface TenGigabitEthernet 0/50
+**interface TenGigabitEthernet 0/50**
- storm-control broadcast pps 3000
+**storm-control broadcast pps 3000**
- description CONEXION SWITCH CORE  IP:  10.1.0.1
+**description CONEXION SWITCH CORE  IP:  10.1.0.1**
- switchport mode trunk
+**switchport mode trunk**
- ip dhcp snooping trust**
+**ip dhcp snooping trust**
 ----
@@ Line 1762: / Line 1761: @@
 ** no shutdown**
 !
@@ Line 1794: / Line 1792: @@
 Ruijie(config)#**snmp-server host 1.1.1.1 version 2c private**        ------>**set SNMP trap version to version 2c**
-----
-Ruijie#show running-config | include interface GigabitEthernet 0/18
-Ruijie#show interfaces description
-Ruijie# show interface status
-Ruijie# show aggregatePort summary
-Ruijie# show interfaces aggregatePort 1
-Ruijie# show aggregatePort load-balance
-Ruijie# show int aggreagtePort 1
-SW1(config)#interface range gigabitEthernet 0/23-24                          ------>configure a range of interfaces with the same commands
-Ruijie# show cpu
-Ruijie# show memory
-Ruijie# show power
-Ruijie# show fan
-Ruijie# show temperature
-Ruijie# show clock
-Ruijie# show log
-Ruijie# more flash:syslog.txt
-Ruijie# dir
-Ruijie# show arp
-Ruijie# show mac-address-table
-Ruijie#show mac-address-table count
-Ruijie# show arp
-Ruijie# show arp detail
-Ruijie# show arp count
-Ruijie# show ip route
-Ruijie# show ip route count
-Ruijie# show ip interface brief
-Ruijie# show interface description
-Ruijie# show interface counters
-Ruijie# **show version**
-Ruijie# **show version slot**
-Ruijie(config)#**show snmp host**
-Ruijie(config)#**show snmp view**
-Ruijie(config)#**show snmp user**
-----
 !
@@ Line 1889: / Line 1813: @@
 **Ruijie#copy running-config startup-config**
-------------------------------------------
+----
-Ruijie>enable
-Ruijie#configure termina
-Ruijie(config)#interface gigabitEthernet 0/1
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control broadcast level 1    ------>storm-control limits the number of broadcast packets to 1% of the bandwidth that is 1G*1%=10M
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control unicast level 1         ------>storm-control limites the number of unknown unicast packets to 1% of the bandwidth that is 1G*1% =10M
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control multicast level 1
-To configure storm control on a port with keyword pps, perform this task:
-Ruijie>enable
-Ruijie#configure termina
-Ruijie(config)#interface gigabitEthernet 0/1
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control broadcast pps 200    ------>storm-control limits the number of broadcast packets to 200 packets per seconds
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control unicast pps 200      ------>storm-control limits the number of unknown unicast packets to 200 packets per seconds
-Ruijie(config-if-GigabitEthernet 0/1)#storm-control multicast 200
-Ruijie(config-if-GigabitEthernet 0/1)#end
-------------------------------------------
-Si tenemos problemas de conectiviad, con un solo cable conectado y es una instalacion nueva aplicar las siguientes lineas:
 Ruijie(config)#no spanning-tree mode
-Ruijie(config)#no spanning-tree vlan 1,3-5,7,9-11     (todas las vlans que apliquen)
+Ruijie(config)#no spanning-tree vlan 1,3-5,7,9-11     (all VLANs)
-------------------------------------------
-Dynamic mode:
-SW1(config)#interface range gigabitEthernet 0/1-2
-SW1(config-if-range)#port-group 1 mode active                            ------>put G0/1 and G0/2 in AP 1 in dynamic mode
-SW1(config-if-range)#exit
-SW1(config)#interface aggregateport 1
-SW1(config-if-AggregatePort 1)#switchport mode trunk                ------>configure AP 1 as Trunk
-SW1(config-if-AggregatePort 1)#exit
-SW2 is the same.
--------------------------------------------
+----