Differences

This shows you the differences between two versions of the page.

--- windows:windows_time_service_ntp [2025/10/07 08:16] – aperez
+++ windows:windows_time_service_ntp [2025/10/07 12:08] (current) – aperez
@@ Line 60: / Line 60: @@
-===== 🕒 NTP Configuration on Aruba CX 6400 (Houston, TX) =====
+===== 🕒 NTP Configuration on Aruba CX 6300 / 6400 (Houston, TX) =====
 To configure the switch to synchronize its time using public NTP servers and apply the correct time zone for Houston (Central Time), run the following commands in **configuration mode**:
@@ Line 178: / Line 178: @@
 ----
+===== 🕒 NTP and DNS Configuration on Aruba 3810M (Houston, TX) =====
+This configuration enables NTP synchronization, DNS resolution, and applies the correct Central Time zone (Houston, TX) with daylight saving rules for the continental U.S. and Canada.
+<code bash>
+configure terminal
+! Enable NTP mode
+timesync ntp
+ntp enable
+! Configure DNS servers for hostname resolution
+ip dns server-address priority 1 8.8.8.8
+ip dns server-address priority 2 1.1.1.1
+! Configure NTP servers (can use hostnames if DNS is working)
+ntp server 0.pool.ntp.org
+ntp server 1.pool.ntp.org
+ntp server 2.pool.ntp.org
+ntp server 3.pool.ntp.org
+! Set time zone to Central Time (UTC−6)
+time timezone -360
+! Enable daylight saving time for continental U.S. and Canada
+time daylight-time-rule continental-us-and-canada
+exit
+write memory
+</code>
+----
+==== 🔍 Verification ====
+Verify NTP synchronization, DNS status, and system time:
+<code bash>
+show ntp status
+show ntp associations
+show ip dns
+show time
+show clock
+</code>
+**Expected results:**
+  * ''System time synchronized to NTP Server …'' → indicates active synchronization.
+  * ''Time zone offset: -360'' → confirms Central Time.
+  * ''Daylight time rule: continental-us-and-canada'' → DST adjustment active.
+  * ''DNS server(s): 8.8.8.8, 1.1.1.1'' → confirms DNS configuration.
+----
+==== 🧠 Notes ====
+  * Aruba 3810M supports **FQDN or IP** for NTP servers — DNS must be reachable.
+  * To use an internal NTP source (e.g. Windows Server), replace pool servers with:
+    <code>
+    ntp server 10.28.64.22
+    </code>
+  * If DNS is unreachable, use IP addresses directly for NTP.
+  * NTP uses UDP port 123; confirm outbound reachability.
+  * Save configuration permanently with ''write memory''.
+----
+----
+===== 🕒 SNTP and DNS — Dell EMC N3048P (DNOS 6.5.3.6, Houston, TX) =====
+Validated configuration for accurate timekeeping with SNTP (unicast), DNS resolvers, Central Time (UTC−6) and U.S. DST.
+<code bash>
+! Already applied (from running-config):
+sntp unicast client enable
+sntp server 216.239.35.0
+sntp server 162.159.200.1
+sntp server 129.6.15.28
+sntp server 132.163.96.5
+clock summer-time recurring USA
+clock timezone -6 minutes 0
+ip name-server "8.8.8.8"
+ip name-server "1.1.1.1"
+exit
+write memory
+</code>
+==== 🔍 Verification ====
+<code bash>
+show sntp
+show clock
+show running-config | include sntp|clock|name-server
+</code>
+**Expected:**
+  * ''SNTP Client Mode: Unicast'' and servers ''Reachable''
+  * ''Clock timezone offset: -6'' and ''DST: USA (active when applicable)''
+  * Last sync time updates periodically (UDP/123 reachable)
+==== 🧠 Notes ====
+  * DNOS 6 in N3000 uses **SNTP** (no full NTP).
+  * If DNS is down, keep servers by **IP** (as configured).
+  * Ensure outbound **UDP/123** is allowed from the chosen source-interface.
+  * Persist with ''write memory'' after any change.
+----
+----
+===== 🕒 NTP and DNS Configuration on Aruba 7220 (AOS 8.12, Houston, TX) =====
+Use IANA timezone names. For Houston, use ''America/Chicago'' (DST automático).
+<code bash>
+configure terminal
+! DNS (opcional, para resolver FQDN)
+ip name-server 8.8.8.8
+ip name-server 1.1.1.1
+! NTP servers (FQDN soportado si hay DNS)
+ntp server 0.pool.ntp.org
+ntp server 1.pool.ntp.org
+ntp server 2.pool.ntp.org
+ntp server 3.pool.ntp.org
+! Zona horaria IANA (Houston)
+clock timezone America/Chicago
+end
+write memory
+</code>
+==== 🔍 Verificación ====
+<code bash>
+show ntp servers
+show ntp status
+show clock
+</code>
+**Esperado:**
+  * Uno de los NTP marcado como peer activo.
+  * ''show clock'' mostrando hora local con ''CDT/CST'' según corresponda (DST automático).
+----
+----
+===== 🕒 NTP and DNS Configuration on Arista 7050QX (EOS 4.13.x, Houston, TX) =====
+This configuration enables DNS resolution, adds public NTP servers, and applies the Central Time zone.
+<code bash>
+configure terminal
+ip name-server 8.8.8.8
+ip name-server 1.1.1.1
+ntp server 0.pool.ntp.org
+ntp server 1.pool.ntp.org
+ntp server 2.pool.ntp.org
+ntp server 3.pool.ntp.org
+clock timezone US/Central
+end
+write memory
+</code>
+----
+==== 🔍 Verification ====
+<code bash>
+show ntp status
+show ntp associations
+show clock
+</code>
+Expected:
+  * One server selected as the system peer.
+  * ''show clock'' shows local time with timezone ''US/Central''.
+----
+==== 🧠 Notes ====
+  * ''ip name-server'' configures DNS resolvers on EOS. :contentReference[oaicite:0]{index=0}
+  * ''ntp server <ip|fqdn>'' adds time sources; EOS NTP is enabled by default. Use ''iburst'' if desired for faster initial sync. :contentReference[oaicite:1]{index=1}
+  * Time zone labels accept **IANA/alias names** like **''US/Central''** or **''America/Chicago''** (''clock timezone ?'' lists options). :contentReference[oaicite:2]{index=2}
+  * To force the source address, use **''ntp local-interface <intf>''** (e.g., **Management1** or a VLAN SVI). :contentReference[oaicite:3]{index=3}
+  * If NTP must traverse **VRF MGMT**, append **''vrf MGMT''** to each server line. :contentReference[oaicite:4]{index=4}
+----
+----
+===== 🕒 NTP and DNS on Cisco Catalyst 9500 (IOS XE 17.12) — Houston, TX =====
+DNS + NTP con zona horaria Central (CST/CDT). ''ip domain-lookup'' no es requerido en esta versión.
+<code bash>
+conf t
+ip name-server 8.8.8.8
+ip name-server 1.1.1.1
+! NTP servers (FQDN soportado)
+ntp server 0.pool.ntp.org
+ntp server 1.pool.ntp.org
+ntp server 2.pool.ntp.org
+ntp server 3.pool.ntp.org
+! (Opcional) Fuente de NTP para dirección estable
+ntp source Loopback0
+! Zona horaria Houston (Central) + DST EE.UU.
+clock timezone CST -6
+clock summer-time CDT recurring 2 Sun Mar 2:00 1 Sun Nov 2:00
+end
+write memory
+</code>
+----
+==== 🔁 (Opcional) Enviar NTP por el VRF de management ====
+Si tu salida a Internet va por **Mgmt-vrf**, usa:
+<code bash>
+conf t
+ntp source Loopback0
+ntp server vrf Mgmt-vrf 0.pool.ntp.org
+ntp server vrf Mgmt-vrf 1.pool.ntp.org
+ntp server vrf Mgmt-vrf 2.pool.ntp.org
+ntp server vrf Mgmt-vrf 3.pool.ntp.org
+end
+write memory
+</code>
+----
+==== 🔍 Verificación ====
+<code bash>
+show hosts                      ! valida resolución DNS
+ping 0.pool.ntp.org             ! (o ping vrf Mgmt-vrf 0.pool.ntp.org)
+show ntp associations
+show ntp status
+show clock detail
+show run | i name-server|ntp|clock
+</code>
+**Esperado:**
+  * Un servidor con ''*'' como **system peer** en ''show ntp associations''.
+  * ''show clock detail'' mostrando CST/CDT y estado de DST.
+  * DNS resolviendo (''show hosts'').
+----
+==== 🧠 Notas ====
+  * Si algún FQDN no resuelve, prueba primero con **IP** para descartar DNS.
+  * Asegura salida **UDP/123** desde la interfaz/VRF usada por NTP.
+  * Puedes marcar un servidor como preferido:
+    <code>ntp server 0.pool.ntp.org prefer</code>
+----
+----