Antonio Perez

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== ArubaInstant_Norma_8.12.0.5_92330 ======
If the **IAP** is part of a **cluster**, the username will be **admin**, and **the password will be the serial number of any AP in the cluster**. If the IAP is running a software version earlier than **ArubaOS 8.5.0.0**, **admin** will remain the default **password**.

**[[https://networkingsupport.hpe.com/downloads|HPE Networking Support Portal]]**

**[[https://support.hpe.com/connect/s/product?language=en_US&kmpmoid=1013490535&tab=driversAndSoftware|HPE Support Center]]**
----



^ Field ^ Value ^
| **Filename**       | ArubaInstant_Norma_8.12.0.5_92330 |
| **Version**        | Access Points v8.12.0.5 (SSR)     |
| **Product Series** |   * 670 Series Outdoor Access Points\\  * 670EX Series Outdoor Access Points\\  * 650 Series Campus Access Points\\  * 630 Series Campus Access Points |
| **Size**           | 45.4 MB                           |
| **Released On**    | Apr 6, 2025                       |
| **Release Notes**  | [[https://example.com/release_notes|Release Notes]] |
| **File Category**  | Software                          |




{{ :aruba_networks:ap:arubainstant_norma_8.12.0.zip |}}
----

{{ :aruba_networks:ap:aruba-instant-8.12.0.5-release-notes.pdf |}}

{{pdfjs 46em >:aruba_networks:ap:aruba-instant-8.12.0.5-release-notes.pdf}}
----
----

====== ArubaOS_Norma_10.7.1.1_92045 ======


^ Field ^ Value ^
| **Filename**       | ArubaOS_Norma_10.7.1.1_92045 |
| **Version**        | Access Points v10.7.1.1 (SSR) |
| **Product Series** |   * 670 Series Outdoor Access Points\\  * 670EX Series Outdoor Access Points\\  * 650 Series Campus Access Points\\  * 630 Series Campus Access Points |
| **Size**           | 106.8 MB |
| **Released On**    | Mar 4, 2025 |
| **Release Notes**  | [[https://example.com/release_notes|Release Notes]] |
| **File Category**  | Software |



{{ :aruba_networks:ap:arubaos_norma_10.7.1.zip |}}


----
{{ :aruba_networks:ap:aos_10.7.1.1-rn.pdf |}}

{{pdfjs 46em >:aruba_networks:ap:aos_10.7.1.1-rn.pdf}}
----



====== ArubaOS_Norma_ArubaOS_Norma_10.8.1.1_96846 ======


{{ :aruba_networks:ap:arubaos_norma_10.8.1.1_96846.zip |}}
----



====== Aruba IAP-635 RW Deployment — Knowledge Base ======
This document describes the full deployment of Aruba IAP-635 (RW regulatory domain) for the South Campus.  
It includes VLAN design, switch configuration, Virtual Controller setup, SSID renaming, verification commands, and troubleshooting references.

===== Table of Contents =====
  * [[#network_topology|Network Topology]]
  * [[#switch_configuration_aruba_6300|Switch Configuration (Aruba 6300)]]
  * [[#virtual_controller_settings_rw|Virtual Controller Settings (RW Controller)]]
  * [[#ssid_renaming_rw|SSID Renaming – RW Controller]]
  * [[#cli_verification_commands|CLI Verification Commands]]
  * [[#notes_and_recommendations|Notes & Recommendations]]

----

===== Network Topology =====

  * **AP Model:** Aruba IAP-635 (RW)
  * **Total RW APs:** 4 units
  * **AP VLAN:** **735**
  * **AP Backhaul VLAN:** **706**
  * **RW Virtual Controller IP:** **172.20.76.20**
  * **Switch:** Aruba 6300 (Access Layer)
  * **Core:** Aruba 6400 (MDF-1)

The RW APs should not join the US Virtual Controller due to different regulatory domain (US vs RW).  
Each side operates its own independent Virtual Controller.

----

===== Switch Configuration (Aruba 6300) =====


! ================================
! Aruba 6300 - AP RW VLAN 735/706
! ================================

! -------- AP 172.20.76.24 / AP_59 --------
  interface 1/1/1
   description AP_172.20.76.24/_44:12:44:cd:ed:45_635(indoor)_AP_59
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 735
   vlan trunk allowed all

! -------- LINK TO AP (VLAN 706) --------
  interface 1/1/2
   description LINK TO AP
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 706
   vlan trunk allowed all

! -------- AP 172.20.76.22 / AP_57 --------
  interface 1/1/3
   description AP_172.20.76.22/_44:12:44:cd:f1:05_635(indoor)_AP_57
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 735
   vlan trunk allowed all

! -------- AP 172.20.76.21 / AP_56 --------
  interface 1/1/4
   description AP_172.20.76.21/_44:12:44:ce:26:7e_635(indoor)_AP_56
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 735
   vlan trunk allowed all

! -------- LINK TO AP (VLAN 706) --------
  interface 1/1/5
   description LINK TO AP
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 706
   vlan trunk allowed all

! -------- AP 172.20.76.23 / AP_58 --------
  interface 1/1/6
   description AP_172.20.76.23/_44:12:44:ce:01:d3_635(indoor)_AP_58
   no shutdown
   mtu 9100
   no routing
   vlan trunk native 735
   vlan trunk allowed all

! ============================
! LAG-1 toward Core 6400 (MDF-1)
! ============================

  interface lag 1
   description Access LAG-1 to MDF-1 - Core 6400
   no shutdown
   no routing
   vlan trunk native 1
   vlan trunk allowed all
   lacp mode active
   loop-protect

  interface 1/1/49
   description Access LAG-1 to MDF-1
   no shutdown
   mtu 9100
   lag 1

  interface 1/1/50
   description Access LAG-1 to MDF-1
   no shutdown
   mtu 9100
   lag 1


===== Virtual Controller Settings (RW Controller) =====

  virtual-controller-country RW
  virtual-controller-ip 172.20.76.20

**Verification commands:**

  show running-config | include virtual
  show swarm state
  show swarm leader
  show aps


**If Virtual Controller appears as 0.0.0.0, set it manually:**


  virtual-controller-ip 172.20.76.20
  commit apply

===== SSID Renaming – RW Controller =====

  configure terminal
  wlan ssid-profile "SFE_WiFi"
   essid "SFE_WiFi-RW"
   exit
  
  wlan ssid-profile "SFE-Guest-WiFi"
   essid "SFE-Guest-WiFi-RW"
   exit
  
  wlan ssid-profile "IoT"
   essid "IoT-RW"
   exit
  
  wlan ssid-profile "SFE_ST"
   essid "SFE_ST-RW"
   exit
  
  wlan ssid-profile "SFE_Staff"
   essid "SFE_Staff-RW"
   exit
  
  wlan ssid-profile "SFE_Student"
   essid "SFE_Student-RW"
   exit
  
  wlan ssid-profile "SFE_Teacher"
   essid "SFE_Teacher-RW"
   exit
  
  wlan ssid-profile "Couper_Portal"
   essid "Couper_Portal-RW"
   exit
  
  commit apply


**Verification:**

  show network
  show network <SSID>


===== CLI Verification Commands =====

==== AP Health and Radios ====
  show aps
  show ap debug system-status
  show ap name <APNAME> status
  show ap debug radio-stats

==== Client/IP Assignment ====

  show client
  show client detail <mac-address>
  show client network <SSID>
  show ip dhcp binding

==== WLAN/SSID Validation ====

  show network
  show network <SSID>
  show wlan ssid-profile

==== VC Cluster and Leadership ====

  show swarm state
  show swarm leader
  show running-config | include virtual

==== Switch VLAN and MTU ====

  show vlan port 1/1/x
  show interface 1/1/x
  show interface 1/1/x | include MTU

==== MTU End-To-End Test ====

  ping 8.8.8.8 size 1472 repeat 5

===== Notes and Recommendations =====

  * RW and US APs cannot join the same Virtual Controller cluster because they run different regulatory domains.
  * RW SSIDs include the “-RW” suffix to avoid SSID duplication inside the same L2/L3 space.
  * VLAN 735 is used for AP access, VLAN 706 for AP uplinks/mesh/internal management.
  * Jumbo MTU (9100) is required end-to-end to avoid fragmentation or CAPWAP instability.
  * Always verify DHCP bindings if clients fail to obtain IP.
  * Ensure each AP is correctly mapped to its trunk native VLAN.

----
----