Antonio Perez

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== SHOW COMMANDS ======

===== show all-timezones =====

Use the show all-timezones command to view all available time zones.

==== Syntax ====

show all-timezones

==== Example ====

The following displays an example of the show all-timezones command output:

{{:aruba_networks:clearpass:show_commands_1_-_hvillanueva.png?600|}}

===== show date =====

Use the show date command to view the system date, time, and time zone information.

==== Syntax ====

show date

==== Example ====

The following displays an example of the show date command output:

{{:aruba_networks:clearpass:show_commands_2_-_hvillanueva.png?600|}}

===== show dns =====

Use the show dns command to view DNS (Domain Name System) servers.

==== Syntax ====

show dns

==== Example ====

The following example of show dns command output displays the DNS servers configured for the current Policy Manager server:

{{:aruba_networks:clearpass:show_commands_3_-_hvillanueva.png?600|}}

===== show domain =====

Use the show domain command to view the Active Directory Domain controller information.

{{:aruba_networks:clearpass:show_commands_4_-_hvillanueva.png?800|}}

==== Syntax ====

show domain
                                                
==== Example ====

The following displays an example of the show domain command output:

{{:aruba_networks:clearpass:show_commands_5_-_hvillanueva.png?600|}}

===== show fipsmode =====

Use the show fipsmode command to find whether FIPS (Federal Information Processing Standard) mode is enabled or disabled.

==== Example ====

The following example shows that FIPS mode is enabled:

{{:aruba_networks:clearpass:show_commands_6_-_hvillanueva.png?600|}}

===== show hostname =====

Use the show hostname command to view the hostname of the current Policy Manager server.

==== Syntax ====

show hostname

==== Example ====

The following displays an example of the show hostname command:

{{:aruba_networks:clearpass:show_commands_7_-_hvillanueva.png?600|}}

===== show ip =====

Use the show ip command to view the IPv4, IPv6, and DNS information of the host.

==== Syntax ====

show ip

==== Example ====

The following example of the show ip command displays the IPv4, IPv6, and DNS information of the host:

{{:aruba_networks:clearpass:show_commands_8_-_hvillanueva.png?600|}}

===== show license =====

Use the show license command to view the Policy Manager license information.

==== Syntax ====

show license

==== Example ====

The following displays an example of the show license command output:

{{:aruba_networks:clearpass:show_commands_9_-_hvillanueva.png?600|}}

===== show ntp =====

Use the show ntp command to view the IP addresses of the primary and secondary Network Time Protocol (NTP) servers configured for the current Policy Manager server.

The show ntp command also displays information such as the NTP authentication key details corresponding to the NTP server configured (for example, Key ID and hash algorithm).

==== Syntax ====

show ntp 

==== Example ====

The following displays an example of the show ntp command output:

{{:aruba_networks:clearpass:show_commands_10_-_hvillanueva.png?600|}}

===== show ports =====

The show ports command shows the status of all the ports, including any filtering on incoming or outgoing traffic on the particular port. If you use the configure port command to filter inbound or outbout traffic on a selected port, the accept or reject rule assigned to the port will be reflected in the output of this command.

==== Syntax ====

show ports  

==== Example ====

The following displays an example of part of the show ports command output:

{{:aruba_networks:clearpass:show_commands_11_-_hvillanueva.png?600|}}

===== show sysinfo =====

Use the show sysinfo command to view the node uptime, disk utilization, and memory utilization information:

==== Syntax ====

show sysinfo

==== Example ====

The following displays an example of the show sysinfo command output:

{{:aruba_networks:clearpass:show_commands_12_-_hvillanueva.png?600|}}

===== show timezone =====

Use the show timezone command to view the current system time zone.

==== Syntax ====

show timezone

==== Example ====

The following displays an example of the show timezone command output:

{{:aruba_networks:clearpass:show_commands_13_-_hvillanueva.png?600|}}

===== show version =====

Use the show version command to view the Policy Manager software version and the hardware model.

==== Syntax ====

show version

==== Example ====

The following displays an example of the show version command output:

{{:aruba_networks:clearpass:show_commands_14_-_hvillanueva.png?600|}}

 --- //[[ing.hvillanueva@gmail.com|Humberto Villanueva]] 2020/12/01 14:59//