Antonio Perez

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
======NBX-100 Quick Config Guide======



  * **1.** Config IP Address.

  Default address = 192.168.1.190

  * Connect Console Cable

  
  ifShow			// Verify IP Address
  nbxIpConfig		// Configure IP Address
  
  

  * **2.** Dialplan, Operation, Default File, Select suitable country file 3 or 4 digit, Import
Modify dialplan:


  PreTranslator Create 2 dialin 8-digit direct mapping
  /                         PreTransId Entry Digits
  /                         ---------- ----- ------
  PreTranslatorEntry Create          2     1 225847
  
  PreTranslator Create 3 dialout CLI pretranslator
  /                         PreTransId Entry Digits
  /                         ---------- ----- ------
  PreTranslatorEntry Create          3     1 1
  
  
  /                             PreTransId Entry OperId Operation  Value
  /                             ---------- ----- ------ ---------  -----
  PreTranslatorOperation Create          2     1      1 stripLead  6
  PreTranslatorOperation Create          2     1      2 prepend    1
  PreTranslatorOperation Create          3     1      1 stripLead  1
  PreTranslatorOperation Create          3     1      2 prepend    225847




  * **3.** System Configuration, System Wide, Enable Autodiscover:

  * a.	Autodiscover Telephones
  * b.	Autodiscover Line Cards
  * c.	Autodiscover Digital Line Cards
  * d.	Add phones to pickupgroup 1


  * **4.** System Configuration, System Settings, Date & Time

  * **5.** System Configuration, Business Identity, Name & Contact info

  * **6.** User Configuration, Users, 
    * a. Select Phone Extention, Modify
      * i. Modify, Ext Nubmer First Name, Last Name

  * **7.** User Configuration, COS, Default User Group, Modify
    * a. Enable Access rights.
 


  * **8.** Device Config, Device Type, select ISDN Board, Modify, 
    * a. Online=Enable



  * **9.** Device Config, Device Type, select Span List, Modify, Span_1 

  * a.	Interfacetype = E1
  * b.	Co Switch = ETSI
  * c.	Framing Type = Double Frame (multiframe without CRC4).
    * i. If problem, try Multiframe with CRC4
  * d.	Line Code = HDB3
  * e.	Line Length = N/A-E1
  * f.	Online = enable


  * **10.** Device Config, Device Type, select PRI Group, Modify, Pri Group 1
    * a. Online = Enable

  * **11.** Dialplan, Pretranslator
    * a. dialin 8 digit direct mapping, Device Using
    * b. Add all ISDN PRI Channel.

  * **12.** Dialplan, Pretranslator,
    * a. Dialout CLI pretranslator, Device Device Using for CLI
    * b. Add All ISDN PRI Channel.

  * **13.** System Configuration, System Wide
    * a. Autodiscover Adjunct = Enable

  * **14.** Device Configuration, Adjunct, Select Adjunct, 
    * a. Modify, Select Associated Telephone
    * b. Button Mappings, Configure Ext Line number

  * **15.**	Report, Call Reporting, Enable


=====Trouble Shooting / Tips=====

====If the incoming volume is low:====

  Device Config, Device Type, select Span List, Modify, Span_1 
  Modify Audio Source Gain: Intput from default 4096 to 6000

====If the outgoing volume is low====
  Device Config, Device Type, select Span List, Modify, Span_1 
  Modify Audio Source Gain: Intput from default 4096 to 6000


The RJ48C T1 connector on the NBX Digital Line Card (both T1 & PRI) is standard T1 DTE configuration as follows:

  PIN NUMBER
  RJ48C     FUNCTION
  9            1          R1, Receive from Network/CSU(Ring)
  1            2          T1  (Tip)
               3          Not Used
  11           4          R   Transmit to Network/CSU (Ring)
  3            5          T   (Tip)
               6          Not Used
               7          Not Used
               8	  Not Used
 

---------------------------





 --- //[[nce@itclatam.com|David Gonzalez]] 2021/04/10 12:35//