======NBX-100 Quick Config Guide====== * **1.** Config IP Address. Default address = 192.168.1.190 * Connect Console Cable ifShow // Verify IP Address nbxIpConfig // Configure IP Address * **2.** Dialplan, Operation, Default File, Select suitable country file 3 or 4 digit, Import Modify dialplan: PreTranslator Create 2 dialin 8-digit direct mapping / PreTransId Entry Digits / ---------- ----- ------ PreTranslatorEntry Create 2 1 225847 PreTranslator Create 3 dialout CLI pretranslator / PreTransId Entry Digits / ---------- ----- ------ PreTranslatorEntry Create 3 1 1 / PreTransId Entry OperId Operation Value / ---------- ----- ------ --------- ----- PreTranslatorOperation Create 2 1 1 stripLead 6 PreTranslatorOperation Create 2 1 2 prepend 1 PreTranslatorOperation Create 3 1 1 stripLead 1 PreTranslatorOperation Create 3 1 2 prepend 225847 * **3.** System Configuration, System Wide, Enable Autodiscover: * a. Autodiscover Telephones * b. Autodiscover Line Cards * c. Autodiscover Digital Line Cards * d. Add phones to pickupgroup 1 * **4.** System Configuration, System Settings, Date & Time * **5.** System Configuration, Business Identity, Name & Contact info * **6.** User Configuration, Users, * a. Select Phone Extention, Modify * i. Modify, Ext Nubmer First Name, Last Name * **7.** User Configuration, COS, Default User Group, Modify * a. Enable Access rights. * **8.** Device Config, Device Type, select ISDN Board, Modify, * a. Online=Enable * **9.** Device Config, Device Type, select Span List, Modify, Span_1 * a. Interfacetype = E1 * b. Co Switch = ETSI * c. Framing Type = Double Frame (multiframe without CRC4). * i. If problem, try Multiframe with CRC4 * d. Line Code = HDB3 * e. Line Length = N/A-E1 * f. Online = enable * **10.** Device Config, Device Type, select PRI Group, Modify, Pri Group 1 * a. Online = Enable * **11.** Dialplan, Pretranslator * a. dialin 8 digit direct mapping, Device Using * b. Add all ISDN PRI Channel. * **12.** Dialplan, Pretranslator, * a. Dialout CLI pretranslator, Device Device Using for CLI * b. Add All ISDN PRI Channel. * **13.** System Configuration, System Wide * a. Autodiscover Adjunct = Enable * **14.** Device Configuration, Adjunct, Select Adjunct, * a. Modify, Select Associated Telephone * b. Button Mappings, Configure Ext Line number * **15.** Report, Call Reporting, Enable =====Trouble Shooting / Tips===== ====If the incoming volume is low:==== Device Config, Device Type, select Span List, Modify, Span_1 Modify Audio Source Gain: Intput from default 4096 to 6000 ====If the outgoing volume is low==== Device Config, Device Type, select Span List, Modify, Span_1 Modify Audio Source Gain: Intput from default 4096 to 6000 The RJ48C T1 connector on the NBX Digital Line Card (both T1 & PRI) is standard T1 DTE configuration as follows: PIN NUMBER RJ48C FUNCTION 9 1 R1, Receive from Network/CSU(Ring) 1 2 T1 (Tip) 3 Not Used 11 4 R Transmit to Network/CSU (Ring) 3 5 T (Tip) 6 Not Used 7 Not Used 8 Not Used --------------------------- --- //[[nce@itclatam.com|David Gonzalez]] 2021/04/10 12:35//