NBX-100 Quick Config Guide

• 1. Config IP Address.

  Default address = 192.168.1.190

• Connect Console Cable

  
  ifShow Verify IP Address nbxIpConfig Configure IP Address
  
  

• 2. Dialplan, Operation, Default File, Select suitable country file 3 or 4 digit, Import Modify dialplan:

  PreTranslator Create 2 dialin 8-digit direct mapping / PreTransId Entry Digits / ———- —– —— PreTranslatorEntry Create 2 1 225847
  PreTranslator Create 3 dialout CLI pretranslator / PreTransId Entry Digits / ———- —– —— PreTranslatorEntry Create 3 1 1
  
  / PreTransId Entry OperId Operation Value / ———- —– —— ——— —– PreTranslatorOperation Create 2 1 1 stripLead 6 PreTranslatorOperation Create 2 1 2 prepend 1 PreTranslatorOperation Create 3 1 1 stripLead 1 PreTranslatorOperation Create 3 1 2 prepend 225847

• 3. System Configuration, System Wide, Enable Autodiscover:
• a. Autodiscover Telephones
• b. Autodiscover Line Cards
• c. Autodiscover Digital Line Cards
• d. Add phones to pickupgroup 1
• 4. System Configuration, System Settings, Date & Time
• 5. System Configuration, Business Identity, Name & Contact info
• 6. User Configuration, Users,

  • a. Select Phone Extention, Modify
    • i. Modify, Ext Nubmer First Name, Last Name
• 7. User Configuration, COS, Default User Group, Modify
  • a. Enable Access rights.
• 8. Device Config, Device Type, select ISDN Board, Modify,

  • a. Online=Enable
• 9. Device Config, Device Type, select Span List, Modify, Span_1
• a. Interfacetype = E1
• b. Co Switch = ETSI
• c. Framing Type = Double Frame (multiframe without CRC4).
  • i. If problem, try Multiframe with CRC4
• d. Line Code = HDB3
• e. Line Length = N/A-E1
• f. Online = enable
• 10. Device Config, Device Type, select PRI Group, Modify, Pri Group 1
  • a. Online = Enable
• 11. Dialplan, Pretranslator
  • a. dialin 8 digit direct mapping, Device Using
  • b. Add all ISDN PRI Channel.
• 12. Dialplan, Pretranslator,
  • a. Dialout CLI pretranslator, Device Device Using for CLI
  • b. Add All ISDN PRI Channel.
• 13. System Configuration, System Wide
  • a. Autodiscover Adjunct = Enable
• 14. Device Configuration, Adjunct, Select Adjunct,

  • a. Modify, Select Associated Telephone
  • b. Button Mappings, Configure Ext Line number
• 15. Report, Call Reporting, Enable

Device Config, Device Type, select Span List, Modify, Span_1 
Modify Audio Source Gain: Intput from default 4096 to 6000

Device Config, Device Type, select Span List, Modify, Span_1 
Modify Audio Source Gain: Intput from default 4096 to 6000

The RJ48C T1 connector on the NBX Digital Line Card (both T1 & PRI) is standard T1 DTE configuration as follows:

PIN NUMBER
RJ48C     FUNCTION
9            1          R1, Receive from Network/CSU(Ring)
1            2          T1  (Tip)
             3          Not Used
11           4          R   Transmit to Network/CSU (Ring)
3            5          T   (Tip)
             6          Not Used
             7          Not Used
             8	  Not Used

— David Gonzalez 2021/04/10 12:35