3com:switch:controller:configuration:script:wx2200_configuration_example_script
wx2200dyn# disp conf # Configuration nvgen'd at 2008-10-29 03:24:55 # Image 6.0.6.1.0 # Model WX2200 # Last change occurred at 2008-10-29 02:49:48 set ip route default 20.20.20.111 1 set system name wx2200dyn set system ip-address 20.20.20.241 set system countrycode CO set service-profile Open ssid-name TSOopen set service-profile Open ssid-type clear set service-profile Open auth-fallthru last-resort set service-profile Open auth-dot1x disable set service-profile Open attr vlan-name V103 set service-profile Secure-802.1X ssid-name TSO-2 set service-profile Secure-802.1X wpa-ie enable set radius server myradius address 20.20.20.2 timeout 5 retransmit 3 deadtime 0 encrypted-key 14041a0a1e012e38212b213036 set server group myradius-group members myradius set enablepass password 0ff65673d5aa7b70f10754a126172d0b1539 set authentication dot1x ssid TSO-2 ** pass-through myradius-group set user admin password encrypted 095b471b1c09120118 set radio-profile default service-profile Secure-802.1X set radio-profile default service-profile Open set ap 1 serial-id l9dq5cd50e080 model AP2750 set ap 1 name MAP01 set ap 1 radio 1 mode enable set vlan 1 port 1 set vlan 1 port 2 set vlan 1 port 3 set interface 1 ip 20.20.20.241 255.255.255.0 set mobility-domain mode seed domain-name TSO-1-Mobilitydomain set network-domain mode member seed-ip 20.20.20.253 affinity 8 wx2200dyn# wx2200dyn# wx2200dyn# disp ver Mobility System Software, Version: 6.0.6.1 REL Copyright (c) 2004 - 2008 3Com Corporation. All rights reserved. Build Information: (build#0) REL_6_0_6_branch 2008-02-06 18:36:00 Model: WX2200 Hardware Mainboard: version 4 ; revision AA ; FPGA version 7 Serial number 9UZL72E9D6E00 Flash: 1.0.0 - 0 Kernel: QNX-630 BootLoader: 6.0 / 6.0.4 wx2200dyn# wx2200dyn# wx2200dyn# disp sess User Sess IP or MAC VLAN Port/ Name ID Address Name Radio ---------------------------- ---- ----------------- --------------- --------- pom2008 27156* 44.44.44.2 V103 AP 1/1 1 session total wx2200dyn# disp tunnel vlan ? <vlan> Character string, max 16 characters wx2200dyn# disp tunnel vlan V103 VLAN Local Address Remote Address State Port LVID RVID ---------------- --------------- --------------- ------- ----- ----- ----- V103 20.20.20.241 20.20.20.253 UP 1025 4096 103 wx2200dyn# wx2200dyn# disp log buff wx2200dyn# TSO-2# TSO-2# TSO-2# disp conf # Configuration nvgen'd at 2008-10-29 09:07:12 # Image 6.0.6.1.0 # Model WX1200 # Last change occurred at 2008-10-29 08:55:08 set ip route default 20.20.20.111 1 set system name TSO-2 set system ip-address 20.20.20.253 set system countrycode CO set timezone BOG -5 0 set service-profile TSO-2 ssid-name TSO-2 set service-profile TSO-2 attr vlan-name V103 set radius client system-ip set radius server RADIUS-TSO-1 address 172.16.0.4 timeout 5 retransmit 3 deadtim e 0 encrypted-key 0828584d051811161f set server group RADIUS-TSO-1-GROUP members RADIUS-TSO-1 set enablepass password 6b24269876340bd036475dd7081b51861a1a set accounting dot1x ssid any ** start-stop RADIUS-TSO-1-GROUP set authentication dot1x ssid any ** pass-through RADIUS-TSO-1-GROUP set accounting system RADIUS-TSO-1-GROUP set user admin password encrypted 030d4f0805002d1e1e5901 set user admin attr service-type 6 set mobility-profile mode enable set radio-profile default auto-tune channel-config disable set radio-profile default auto-tune power-config enable set radio-profile default service-profile TSO-2 set vlan-profile default vlan V101 tag 101 set ap 1 port 1 model AP2750 set ap 1 name AP2750 set ap 1 location LABORATORIO TSO-2 set ap 1 contact Antonio Perez set ap 1 radio 1 channel 10 mode enable set ip snmp server enable set ip telnet server enable set ip ssh server disable set load-balancing mode disable set port 1 name AP2750 set port poe 1 enable set snmp community name public access read-only set snmp community name private access read-write set vlan 1 name default tunnel-affinity 10 set vlan 1 port 7 set vlan 1 port 8 set vlan 103 name V103 tunnel-affinity 10 set vlan 103 port 8 tag 103 set vlan 104 name V104 tunnel-affinity 10 set vlan 104 port 8 tag 104 set vlan 105 name V105 tunnel-affinity 10 set vlan 105 port 8 tag 105 set spantree disable port 8 1 set spantree priority 32768 vlan 103 set spantree priority 32768 vlan 104 set spantree priority 32768 vlan 105 set interface 1 ip 20.20.20.253 255.255.255.0 set interface 1 ip dhcp-server disable start 192.168.1.1 stop 192.168.1.254 set mobility-domain mode seed domain-name TSO-2-MOBILITY-DOMAIN set network-domain mode seed domain-name TSO set network-domain peer 20.20.20.241 set network-domain mode member seed-ip 20.20.20.241 set network-domain mode member seed-ip 20.20.20.253 affinity 10 set security acl ip portalacl permit udp 0.0.0.0 255.255.255.255 eq 68 0.0.0.0 2 55.255.255.255 eq 67 set security acl ip portalacl deny 0.0.0.0 255.255.255.255 capture commit security acl portalacl TSO-2# TSO-2# TSO-2# disp sess User Sess IP or MAC VLAN Port/ Name ID Address Name Radio ---------------------------- ---- ----------------- --------------- --------- 0 sessions total TSO-2# disp tunnel vlan ? <vlan> Character string, max 16 characters TSO-2# disp tunnel vlan V103 VLAN Local Address Remote Address State Port LVID RVID ---------------- --------------- --------------- ------- ----- ----- ----- V103 20.20.20.253 20.20.20.241 UP 1024 103 4096 TSO-2# TSO-2# TSO-2# disp ver Mobility System Software, Version: 6.0.6.1 REL Copyright (c) 2004 - 2008 3Com Corporation. All rights reserved. Build Information: (build#0) REL_6_0_6_branch 2008-02-06 18:36:00 Model: WX1200 Hardware Mainboard: version 15 ; revision AB ; FPGA version 31 Serial number 28WM9GM48AE40 Flash: 1.0.0 - 0 Kernel: QNX-630 BootLoader: 4.20 / 6.0.10 TSO-2# TSO-2#
— David Gonzalez 2021/03/31 15:49
3com/switch/controller/configuration/script/wx2200_configuration_example_script.txt · Last modified: 2021/04/03 13:20 by dgonzalez