aruba_networks:switch:4800:irf_configuration:script_cnfg_4800
Differences
This shows you the differences between two versions of the page.
aruba_networks:switch:4800:irf_configuration:script_cnfg_4800 [2021/02/27 17:52] – created dgonzalez | aruba_networks:switch:4800:irf_configuration:script_cnfg_4800 [2021/03/10 16:17] (current) – removed dgonzalez | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====IRF CONFIGURATION===== | ||
- | |||
- | Next we will see the script of a configuration made to a 4800, where the IRF links were enabled and it is explained with short notes to clear up doubts | ||
- | |||
- | irf mac-address persistent timer | ||
- | irf auto-update enable | ||
- | undo irf link-delay | ||
- | | ||
- | snmp-agent | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | # Configure Switch 1. | ||
- | < | ||
- | [Switch1] irf member 1 renumber 1 | ||
- | Warning: Renumbering the switch number may result in configuration change or loss. | ||
- | Continue? | ||
- | [Switch1] irf member 1 irf-port 1 port 2 | ||
- | # Configure Switch 2. | ||
- | < | ||
- | [Switch2] irf member 1 renumber 2 | ||
- | Warning: Renumbering the switch number may result in configuration change or loss. | ||
- | Continue? | ||
- | [Switch2] irf member 1 irf-port 1 port 2 | ||
- | | ||
- | | ||
- | [Switch2] irf member 1 irf-port 2 port 3 | ||
- | # Configure Switch 3. | ||
- | < | ||
- | [Switch3] irf member 1 renumber 3 | ||
- | Warning: Renumbering the switch number may result in configuration change or loss. | ||
- | Continue? | ||
- | [Switch3] irf member 1 irf-port 2 port 3 | ||
- | 2) Power off the three devices. Connect them as shown in Figure 1-9 with stack cables. Power them | ||
- | on, and the stack is formed. | ||
- | | ||
- | |||
- | NOTE: CONSIDER THE FOLLOWING: | ||
- | |||
- | | ||
- | THE SWITCH DIFFERENCES THE PHYSICAL PORT FROM THE LOGIC. | ||
- | EXAMPLE | ||
- | |||
- | A 10CX4 MODULE IN THE SWITCH WOULD BE IDENTIFIED AS FOLLOWS: | ||
- | |||
- | IRF-PORT 1 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 1 | ||
- | IRF-PORT 2 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 2 | ||
- | |||
- | |||
- | **IRF configuration** | ||
- | |||
- | |||
- | < | ||
- | | ||
- | | ||
- | -------------------------------------------------------- | ||
- | * indicates the device is the master. | ||
- | + indicates the device through which the user logs in. | ||
- | |||
- | |||
- | TWO 10CX4 MODULES IN THE SWTICH WOULD BE IDENTIFIED AS FOLLOWS: | ||
- | |||
- | IRF-PORT 1 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 1 AND PORT 2 (READING THE 4 PHYSICAL PORTS FROM LEFT TO RIGHT) | ||
- | IRF-PORT 2 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT PORT 3 AND PORT 4 | ||
- | |||
- | |||
- | **IRF configuration** | ||
- | |||
- | |||
- | < | ||
- | | ||
- | | ||
- | -------------------------------------------------------- | ||
- | * indicates the device is the master. | ||
- | + indicates the device through which the user logs in. | ||
- | | ||
- | |||
- | IN THE CASE THAT YOU ONLY WANT TO JOIN 2 MACHINES IN SERIOUS STACK IN THE FOLLOWING WAY (PLACED IN THE LEFT MODULE AND THEY ARE ALWAYS CROSSED): | ||
- | |||
- | |||
- | < | ||
- | | ||
- | | ||
- | | ||
- | -------------------------------------------------------- | ||
- | * indicates the device is the master. | ||
- | + indicates the device through which the user logs in. | ||
- | | ||
- | |||
- | FOR IT TO WORK YOU MUST SAVE IN THE SAME FILE AND BETTER TURN OFF THE TWO MACHINES (POWER OFF WITHOUT CURRENT AND TURN THEM ON.) | ||
- | |||
- | |||
- | FOR THE CASE OF 3 MACHINES, IT WOULD BE AS FOLLOWS: | ||
- | |||
- | |||
- | MACHINE 1: | ||
- | |||
- | irf member 1 renumber 1 | ||
- | irf member 1 irf-port 1 port 1 | ||
- | irf member 1 irf-port 2 port 2 | ||
- | |||
- | IRF-PORT 1 (LOGIC PORT) WOULD JOIN THE PHYSICAL PORT 1 | ||
- | IRF-PORT 2 (LOGIC PORT) WOULD JOIN THE PHYSICAL PORT 2 | ||
- | |||
- | MACHINE 2: | ||
- | |||
- | irf member 1 renumber 2 | ||
- | irf member 2 irf-port 1 port 1 | ||
- | irf member 2 irf-port 2 port 2 | ||
- | |||
- | MACHINE 3: | ||
- | |||
- | irf member 1 renumber 3 | ||
- | irf member 3 irf-port 1 port 1 | ||
- | irf member 3 irf-port 2 port 2 | ||
- | |||
- | SAVE ALL THE MACHINES SAME FILE EJM: ITC.CFG | ||
- | AND SHUTDOWN AND RESTART. | ||
- | |||
- | to see the configuration and status of the irf by machine | ||
- | |||
- | |||
- | disp irf confi | ||
- | |||
- | |||
- | ---------------- | ||
- | |||
- | The final procedure is as follows: | ||
- | |||
- | machine 1: | ||
- | |||
- | < | ||
- | | ||
- | [Devicea] irf member 1 renumber 1 | ||
- | Warning: Renumbering the switch number may result in configuration change or loss. | ||
- | Continue? [Y/N]:y | ||
- | | ||
- | [DeviceA] interface ten-gigabitethernet 1/1/1 | ||
- | [DeviceA-Ten-GigabitEthernet1/ | ||
- | [DeviceA] interface ten-gigabitethernet 1/1/2 | ||
- | [DeviceA-Ten-GigabitEthernet1/ | ||
- | [DeviceA] irf-port 1/2 | ||
- | [DeviceA-irf-port1/ | ||
- | [DeviceA-irf-port1/ | ||
- | [DeviceA] interface ten-gigabitethernet 1/1/1 | ||
- | [DeviceA-Ten-GigabitEthernet1/ | ||
- | [DeviceA] interface ten-gigabitethernet 1/1/2 | ||
- | [DeviceA-Ten-GigabitEthernet1/ | ||
- | [DeviceA-Ten-GigabitEthernet1/ | ||
- | < | ||
- | | ||
- | | ||
- | [DeviceA] irf-port-configuration active | ||
- | |||
- | |||
- | |||
- | MACHINE 2: | ||
- | |||
- | < | ||
- | | ||
- | [DeviceB] irf member 1 renumber 2 | ||
- | Warning: Renumbering the switch number may result in configuration change or loss. | ||
- | Continue? [Y/N]:y | ||
- | | ||
- | [DeviceB] interface ten-gigabitethernet 2/1/1 | ||
- | [DeviceB-Ten-GigabitEthernet1/ | ||
- | [DeviceB] interface ten-gigabitethernet 2/1/2 | ||
- | [DeviceB-Ten-GigabitEthernet1/ | ||
- | [DeviceB] irf-port 2/1 | ||
- | [DeviceB-irf-port2/ | ||
- | [DeviceB-irf-port2/ | ||
- | [DeviceB] interface ten-gigabitethernet 2/1/1 | ||
- | [DeviceB-Ten-GigabitEthernet2/ | ||
- | [DeviceB] interface ten-gigabitethernet 2/1/2 | ||
- | [DeviceB-Ten-GigabitEthernet2/ | ||
- | [DeviceB-Ten-GigabitEthernet2/ | ||
- | < | ||
- | | ||
- | | ||
- | [DeviceB] irf-port-configuration active | ||
- | | ||
- | | ||
- | | ||