Differences

This shows you the differences between two versions of the page.

--- aruba_networks:switch:4800:irf_configuration:script_cnfg_4800 [2021/02/27 17:52] – created dgonzalez
+++ aruba_networks:switch:4800:irf_configuration:script_cnfg_4800 [2021/03/10 16:17] (current) – removed dgonzalez
@@ Line 1: / Line 1: @@
-=====IRF CONFIGURATION=====
-Next we will see the script of a configuration made to a 4800, where the IRF links were enabled and it is explained with short notes to clear up doubts
-  irf mac-address persistent timer
-   irf auto-update enable
-   undo irf link-delay
-  snmp-agent
-   snmp-agent local-engineid 8000002B030022572789C1
-   snmp-agent community read public
-   snmp-agent community write private
-   snmp-agent community read snmpmenro
-   snmp-agent community write snmpmenrw
-   snmp-agent sys-info version all
-   snmp-agent target-host trap address udp-domain 10.1.1.40 udp-port 5000 params securityname snmpmenro
-  # Configure Switch 1.
-  <Switch1> system-view
-  [Switch1] irf member 1 renumber 1
-  Warning: Renumbering the switch number may result in configuration change or loss.
-  Continue?[Y/N]:y
-  [Switch1] irf member 1 irf-port 1 port 2
-  # Configure Switch 2.
-  <Switch2>system-view
-  [Switch2] irf member 1 renumber 2
-  Warning: Renumbering the switch number may result in configuration change or loss.
-  Continue?[Y/N]:y
-  [Switch2] irf member 1 irf-port 1 port 2
-  [Switch2] irf member 1 irf-port 2 port 3
-  # Configure Switch 3.
-  <Switch3> system-view
-  [Switch3] irf member 1 renumber 3
-  Warning: Renumbering the switch number may result in configuration change or loss.
-  Continue?[Y/N]:y
-  [Switch3] irf member 1 irf-port 2 port 3
-) Power off the three devices. Connect them as shown in Figure 1-9 with stack cables. Power them
-  on, and the stack is formed.
-NOTE:  CONSIDER THE FOLLOWING:
-THE SWITCH DIFFERENCES THE PHYSICAL PORT FROM THE LOGIC.
-EXAMPLE
-A 10CX4 MODULE IN THE SWITCH WOULD BE IDENTIFIED AS FOLLOWS:
-IRF-PORT 1 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 1
-IRF-PORT 2 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 2
-**IRF configuration**
-  <4800G>DIS IRF configuration
-   MemberID     NewID     IRF-Port1       IRF-Port2
-          1         1               2
-  --------------------------------------------------------
-    * indicates the device is the master.
-   + indicates the device through which the user logs in.
-TWO 10CX4 MODULES IN THE SWTICH WOULD BE IDENTIFIED AS FOLLOWS:
-IRF-PORT 1 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT 1 AND PORT 2 (READING THE 4 PHYSICAL PORTS FROM LEFT TO RIGHT)
-IRF-PORT 2 (PUERTO LOGICO) WOULD JOIN THE PHYSICAL PORT PORT 3 AND PORT 4
-**IRF configuration**
-  <4800G>DIS IRF configuration
-   MemberID     NewID     IRF-Port1       IRF-Port2
-          1         1 2              3 4
-  --------------------------------------------------------
-   * indicates the device is the master.
-   + indicates the device through which the user logs in.
-IN THE CASE THAT YOU ONLY WANT TO JOIN 2 MACHINES IN SERIOUS STACK IN THE FOLLOWING WAY (PLACED IN THE LEFT MODULE AND THEY ARE ALWAYS CROSSED):
-  <4800G>DIS IRF configuration
-   MemberID     NewID     IRF-Port1       IRF-Port2
-          1         1               2
-   *+2          2         1               2
-  --------------------------------------------------------
-   * indicates the device is the master.
-   + indicates the device through which the user logs in.
-FOR IT TO WORK YOU MUST SAVE IN THE SAME FILE AND BETTER TURN OFF THE TWO MACHINES (POWER OFF WITHOUT CURRENT AND TURN THEM ON.)
-FOR THE CASE OF 3 MACHINES, IT WOULD BE AS FOLLOWS:
-MACHINE 1:
-  irf member 1 renumber 1
-  irf member 1 irf-port 1 port 1
-  irf member 1 irf-port 2 port 2
-IRF-PORT 1 (LOGIC PORT) WOULD JOIN THE PHYSICAL PORT 1
-IRF-PORT 2 (LOGIC PORT) WOULD JOIN THE PHYSICAL PORT 2
-MACHINE 2:
-  irf member 1 renumber 2
-  irf member 2 irf-port 1 port 1
-  irf member 2 irf-port 2 port 2
-MACHINE 3:
-  irf member 1 renumber 3
-  irf member 3 irf-port 1 port 1
-  irf member 3 irf-port 2 port 2
-SAVE ALL THE MACHINES SAME FILE EJM: ITC.CFG
-AND SHUTDOWN AND RESTART.
-to see the configuration and status of the irf by machine
-  disp irf confi
-----------------
-The final procedure is as follows:
-machine 1:
-  <DeviceA> system-view
-  [Devicea] irf member 1 renumber 1
-  Warning: Renumbering the switch number may result in configuration change or loss.
-  Continue? [Y/N]:y
-  [DeviceA] interface ten-gigabitethernet 1/1/1
-  [DeviceA-Ten-GigabitEthernet1/1/2] shutdown
-  [DeviceA] interface ten-gigabitethernet 1/1/2
-  [DeviceA-Ten-GigabitEthernet1/1/2] shutdown
-  [DeviceA] irf-port 1/2
-  [DeviceA-irf-port1/2] port group interface ten-gigabitethernet 1/1/1
-  [DeviceA-irf-port1/2] port group interface ten-gigabitethernet 1/1/2
-  [DeviceA] interface ten-gigabitethernet 1/1/1
-  [DeviceA-Ten-GigabitEthernet1/1/1] undo shutdown
-  [DeviceA] interface ten-gigabitethernet 1/1/2
-  [DeviceA-Ten-GigabitEthernet1/1/2] undo shutdown
-  [DeviceA-Ten-GigabitEthernet1/1/2]save itc.cfg
-  <DeviceA>reboot
-  [DeviceA] irf-port-configuration active
-MACHINE 2:
-  <DeviceB> system-view
-  [DeviceB] irf member 1 renumber 2
-  Warning: Renumbering the switch number may result in configuration change or loss.
-  Continue? [Y/N]:y
-  [DeviceB] interface ten-gigabitethernet 2/1/1
-  [DeviceB-Ten-GigabitEthernet1/1/2] shutdown
-  [DeviceB] interface ten-gigabitethernet 2/1/2
-  [DeviceB-Ten-GigabitEthernet1/1/2] shutdown
-  [DeviceB] irf-port 2/1
-  [DeviceB-irf-port2/1] port group interface ten-gigabitethernet 2/1/1
-  [DeviceB-irf-port2/1] port group interface ten-gigabitethernet 2/1/2
-  [DeviceB] interface ten-gigabitethernet 2/1/1
-  [DeviceB-Ten-GigabitEthernet2/1/1] undo shutdown
-  [DeviceB] interface ten-gigabitethernet 2/1/2
-  [DeviceB-Ten-GigabitEthernet2/1/2] undo shutdown
-  [DeviceB-Ten-GigabitEthernet2/1/2]save itc.cfg
-  <DeviceB>reboot
-  [DeviceB] irf-port-configuration active