Differences

This shows you the differences between two versions of the page.

--- cisco:switch:configure_igmp_snooping_settings_on_a_switch_through_the_cli [2020/10/23 22:24] – hvillanueva
+++ cisco:switch:configure_igmp_snooping_settings_on_a_switch_through_the_cli [2020/10/24 00:17] (current) – hvillanueva
@@ Line 39: / Line 39: @@
 **Step 2.** From the Privileged EXEC mode of the switch, enter the Global Configuration mode by entering the following:
-{{:cisco:switch:configure_igmp_snooping_2_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_2_-_hvillanueva.png?800|}}
 **Step 3.** To globally enable IGMP snooping on the switch, enter the following:
-{{:cisco:switch:configure_igmp_snooping_3_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_3_-_hvillanueva.png?800|}}
 **Step 4.** (Optional) To globally enable IGMP snooping querier, enter the following:
-{{:cisco:switch:configure_igmp_snooping_4_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_4_-_hvillanueva.png?800|}}
 You should now have successfully configured the global IGMP snooping settings on your switch.
@@ Line 55: / Line 55: @@
 **Step 1.** To enable IGMP snooping on a specific VLAN, enter the following:
-{{:cisco:switch:configure_igmp_snooping_5_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_5_-_hvillanueva.png?800|}}
 **Note:** In this scenario, the IGMP snooping settings for VLAN 30 are being configured.
@@ Line 61: / Line 61: @@
 **Step 2.** (Optional) To allow the multicast router to automatically learn the connected ports, enter the following:
-{{:cisco:switch:configure_igmp_snooping_6_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_6_-_hvillanueva.png?800|}}
 **Step 3.** (Optional) To enable the IGMP snooping Immediate Leave processing on a VLAN, enter the following:
-{{:cisco:switch:configure_igmp_snooping_7_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_7_-_hvillanueva.png?800|}}
 **Step 4.** In the Global Configuration mode, enter the VLAN Interface Configuration context by entering the following:
-{{:cisco:switch:configure_igmp_snooping_8_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_8_-_hvillanueva.png?800|}}
 **Step 5.** To configure the IGMP last member query counter, enter the following:
-{{:cisco:switch:configure_igmp_snooping_9_-_hvillanueva.png?400|}}
+{{:cisco:switch:configure_igmp_snooping_9_-_hvillanueva.png?800|}}
+**Note:** In this example, the last member query counter is set to 3.
+**Step 6.** Enter the exit command to go back to the Global Configuration mode:
+{{:cisco:switch:configure_igmp_snooping_10_-_hvillanueva.png?800|}}
+**
+Step 7.** To enable the IGMP Snooping querier on a specific VLAN, enter the following:
+{{:cisco:switch:configure_igmp_snooping_11_-_hvillanueva.png?800|}}
+**Step 8.** To enable IGMP querier election mechanism of an IGMP snooping querier on a specific VLAN, enter the following:
+{{:cisco:switch:configure_igmp_snooping_12_-_hvillanueva.png?800|}}
+**Step 9.** To configure the IGMP version of an IGMP Snooping querier on a specific VLAN, enter the following:
+{{:cisco:switch:configure_igmp_snooping_13_-_hvillanueva.png?800|}}
+**Step 10.** To define the source IP address that the IGMP snooping querier uses, enter the following:
+{{:cisco:switch:configure_igmp_snooping_14_-_hvillanueva.png?800|}}
+**Step 11.** Enter the exit command to go back to the Privileged EXEC mode:
+{{:cisco:switch:configure_igmp_snooping_15_-_hvillanueva.png?800|}}
+==== Display IGMP Snooping Settings on a VLAN ====
+**Step 1.** To display the IGMP snooping configuration for a specific VLAN, enter the following:
+{{:cisco:switch:configure_igmp_snooping_16_-_hvillanueva.png?800|}}
+**Step 2.** (Optional) In the Privileged EXEC mode of the switch, save the configured settings to the startup configuration file by entering the following:
+{{:cisco:switch:configure_igmp_snooping_17_-_hvillanueva.png?800|}}