Antonio Perez - 3com:tippingpoint:x506:general_configuration

allow_control_of_firewall_x5_only_through_serial_port

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T21:11:11+00:00

ALLOW CONTROL OF FIREWALL X5 ONLY THROUGH SERIAL PORT Symptoms: How to allow control of the X5 Firewall only through the serial port * How to disable http access to the Firewall * How to disable https access to the Firewall * How to disable ssh access to the Firewall

block_remote_proxy_site

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:19:36+00:00

HOW CAN I BLOCK REMOTE PROXY SITE Symptoms: * How can I block Remote Proxy site * Remote proxies not blocked by the Web Site filter * Specific Remote Proxy site not block by Web Content Filter Facts: * 3Com * Remote Proxy site * X Family

cannot_set_up_a_pptp_vpn_from_microsoft_windows

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:01:52+00:00

CANNOT SET UP A PPTP VPN FROM MICROSOFT WINDOWS VISTA (TM) TO X-FAMILY USING AUTHENTICATION VIA JUNIPER/FUNK STEEL BELTED RADIUS SERVER Symptoms: * Cannot set up a PPTP VPN from Microsoft Windows Vista (TM) to X-family using authentication via Juniper/Funk Steel Belted RADIUS Server

cannot_set_up_a_pptp_vpn_from_windows_vista_to_x-family_using_authentication_via_juniper-funk_steel_belted_radius_server

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T15:29:58+00:00

CANNOT SET UP A PPTP VPN FROM MICROSOFT WINDOWS VISTA (TM) TO X-FAMILY USING AUTHENTICATION VIA JUNIPER/FUNK STEEL BELTED RADIUS SERVER Problem: Cannot set up a PPTP VPN from Microsoft Windows Vista (TM) to X-family using authentication via Juniper/Funk Steel Belted RADIUS Server

cannot_set_up_l2tp_ipsec_vpn_microsoft_windows_vista

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T14:58:25+00:00

CANNOT SET UP A L2TP/IPSEC VPN FROM MICROSOFT WINDOWS VISTA Symptoms: * Cannot set up a L2TP/IPSec VPN from Microsoft Windows Vista (TM) to X-family Facts: * 3CRTPX505-73 * 3CRTPX505-96 * 3CRTPX506-96 * 3CRX506-96 * 3CRTPX5-25-96 * 3CRTPX5-U-96

configuration_client_vpn

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T21:32:04+00:00

PC CONNECTION CONFIGURATION * Start of configuration * Create a new connection VPN configuration on PC * Click next to continue * Select the virtual private network connection * Write the name of the Organization or a badge of the same.

data_loss_due_to_improper_shutdown

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T15:55:29+00:00

DEVICE WAS NOT GRACEFULLY SHUTDOWN. DATA MAY HAVE BEEN LOST X Family Firewall - Event logs no longer displayed Symptoms: * Event logs no longer displayed * “No records were found” error * Event logs showing empty logs while entries count is not null

error_741_when_configuring_pptp_vpn_from_microsoft_windows

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T15:15:10+00:00

TRYING TO SET UP A PPTP VPN FROM MICROSOFT WINDOWS VISTA (TM) TO X-FAMILY RESULTS IN ERROR 741 ON VISTA PC. Problem: * Trying to set up a PPTP VPN from Microsoft Windows Vista (TM) to X-family results in Error 741 on Vista PC. Fact: * 3CRTPX505-73

export_a_snapshot_of_the_system_to_an_external_file_from_the_cli

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T15:05:29+00:00

CAN I EXPORT A SNAPHOT OF THE SYSTEM TO AN EXTERNAL FILE FROM THE CLI? Symptoms: * How do I save a copy of a snaphot to an external file from the CLI? * Is there any way to export a snapshot from the CLI? * What is the CLI command to save a snapshot file.?

firewall_fails_to_setup_ipsec_tunnel_to_cisco_router

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T19:53:58+00:00

FIREWALL FAILS TO SETUP IPSEC TUNNEL TO CISCO ROUTER Symptoms: * XFamily Firewall fails to setup IPsec Tunnel to CISCO Router Facts: * Error: “INVALIDEXCHANGETYPE” * CISCO 2821 * VPN * IKE * Pre-Shared Key * X Family * X5 * X506

get_an_ip_address_via_dhcp_on_any_ports

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T21:04:11+00:00

HOW TO GET AN IP ADDRESS VIA DHCP ON PORTS OTHER THAN 1 ON A X-FAMILY DEVICE? Symptoms: How to get an IP address via DHCP on ports other than 1 on a X-Family device? * How to configure DHCP on ports 2, 3, 4 or 5 on a X-Family device? * Getting an IP address via DHCP on ports other than

high_availability

Anonymous (anonymous@undisclosed.example.com) — 2021-04-09T14:26:28+00:00

HIGH AVAILABILITY Overview * Dual-box solution * Protects against “catastrophic” unit failure * Loss of power * Assumes standby device and network maintains power… * Software failure * Minimise downtime during software upgrade cycles

internal_interfaces_configuration

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:14:25+00:00

HOW DO I CONFIGURE THE INTERNAL INTERFACES? Symptoms: * How do I configure the Internal Interfaces? Facts: * High Availability * X5 * X506 * X505 * Internal Interfaces Causes: * There is some confusion in both the Online Help and in the paper documentation over the configuration of the internal interfaces on a High Availability pair of X-family devices.

ipsec_vpn_setup_example_between_a_superstack_3_firewall_in_standard_mode_and_an_x506_in_nat_mode

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T20:27:46+00:00

IPSEC VPN SETUP EXAMPLE BETWEEN A SUPERSTACK 3 FIREWALL IN STANDARD MODE AND AN X506 IN NAT MODE Here follows screen shots of the configuration for the X Family running X3.1.2098 and SS3 Firewall running v6.3.3 in order to establish an IPSEC VPN tunnel. The SS3 Firewall is in Standard mode and the X series Firewall is in NAT mode.

limitation_on_using_dhcp_relay_over_vpn

Anonymous (anonymous@undisclosed.example.com) — 2021-04-16T23:34:43+00:00

LIMITATION ON USING DHCP RELAY OVER VPN Symptoms: * Limitation on using DHCP Relay over VPN * DHCP Relay not working over the VPN tunnel * PC not getting an IP address over the VPN tunnel Facts: * 3CRTPX5-U-96 * 3CRX506-96 * X5 * X506

monitoring_x-family_with_adventnet_firewall_analyzer

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:09:58+00:00

HOW DO I MONITOR X-FAMILY WITH ADVENTNET FIREWALL ANALYZER? Symptoms: * How do I Monitor X-family with AdventNet Firewall Analyzer? Facts: * AdventNet * ManageEngine * Firewall Analyzer * X5 * X506 * 3CRX5-U-96 * 3CRX5-25-96 * 3CRX506-96

procedure_cisco_asa_vpn_and_3com_tpp

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T17:14:47+00:00

PROCEDURE: CISCO ASA VPN AND 3COM TPP SWITCH ROUTER: 10.57.0.1 SWITCH ROUTER: 192.168.0.1 TPP 3COM CONFIGURATION: CREATE AN IKE PROPOSALS Apply static routes if the network to be reached is not that of the lan interface: CISCO ASA CONFIGURATION:

recovery_password

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T19:46:48+00:00

PROCEDURE PASSWORD RECOVERY TIPPING POINT Fix: * 1. Establish serial communication between the PC and the IPS through the console port. * 2. Restart the IPS. * 3. When the Tipping Point logo appears in the TeraTerm or HyperTerminal window, immediately afterwards the word “loading” appears on the screen. At this time you must enter the key

restore_to_a_previously_defined_state

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T16:47:41+00:00

RESTORE TO A PREVIOUSLY DEFINED STATE The process to perform a reset to a previous state is described in detail below. * **Boot**ITCORP# boot list-image List available images remove-image Remove image rollback Roll back image ITCORP# boot list-image X3.0.0.2090 X2.5.2.6836 ITCORP# boot rollback Are you sure? :y

site_to_site_ipsec_vpn

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T20:03:18+00:00

Site to Site IPSEC VPN Setup Guidelines for the X505 (Static IP) and 3CR870-95/3CR860-95 (Static IP) In Main mode Here follows screen shots of the configuration for the X505 and 3cr870-95/3cr860-95 required to establish an IPSEC site to site VPN tunnel in main mode.

the_2_native_implicit_firewall_rules

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:38:36+00:00

THE 2 NATIVE IMPLICIT FIREWALL RULES Symptoms: * What are the 2 Native Implicit Firewall rules * Any hidden Firewall Rules * Any Implicit Firewall Rules Facts: * Implicit Firewall rules * 3DES * X Family * X5 * X506 Causes: *

the_4_default_firewall_rules

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:33:08+00:00

WHAT ARE THE 4 DEFAULT FIREWALL RULES Symptoms: * What are the 4 Default Firewall rules * Any Factory Firewall rules * Any Firewall rules for basic services Facts: * Default Firewall rules *X Family *X5 *X506 Causes: The X Family firewalls have 4 default firewall rules, those rules are there to facilitate basic services.

unable_to_https_to_public_ip_address_of_x5_over_ipsec_tunnel

Anonymous (anonymous@undisclosed.example.com) — 2021-04-16T23:37:07+00:00

UNABLE TO HTTPS TO PUBLIC IP ADDRESS OF X5 OVER IPSEC TUNNEL Symptoms: * Unable to https to public IP address of X5 over IPSec tunnel Facts: * X Family * X5 * X506 * Firewall * https * http * External IP Address * Firewall rules and services all WAN to this device

unit_performance_comparison

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T15:42:19+00:00

UNIT PERFORMANCE COMPARISON Symptoms: * Unit performance comparison * Total number of concurrent connection Facts: * 3CRTPX5-U-96 * 3CRTPX5-96 * X5 * X Family * X506 Fixes: X Family System Performance: X505 * X5 - 25 User license:

unit_reset_to_factory_defaults

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T20:49:20+00:00

UNIT RESET TO FACTORY DEFAULTS Symptoms: * Unit Reset to Factory Defaults * How do I Reset the unit to the default values * Revert X5 to Factory * Revert X506 to Factory Facts: Factory Reset * X Family * X5 * X506 Fixes: * WARNING:The Reset of the X Family Firewall to Factory Default values using the Debug procedure described below will:

users_authenticated_via_ldap_are_not_placed_in_the_correct

Anonymous (anonymous@undisclosed.example.com) — 2021-04-07T21:24:33+00:00

USERS AUTHENTICATED VIA LDAP ARE NOT PLACED IN THE CORRECT Symptoms: * Users authenticated via LDAP are not placed in the correct User Privileged Group * How do I define a user so it is affected to the correct Privileged Group? * Active directory is not providing the correct Privileged Group return attribute.

web_content_filters_bypass_using_search_engine_caching

Anonymous (anonymous@undisclosed.example.com) — 2021-04-08T16:29:55+00:00

WEB CONTENT FILTERS BYPASS USING SEARCH ENGINE CACHING Symptoms: * Web Content filter not working * Web Content filter not blocking sites using MSN Web Cache * Web Content filter not blocking sites using Yahoo Web Cache * Web Content filter not blocking sites using Google Web Cache