aruba_networks:switch:4800:irf_configuration:error_the_device_is_not_in_the_current_irf
Differences
This shows you the differences between two versions of the page.
aruba_networks:switch:4800:irf_configuration:error_the_device_is_not_in_the_current_irf [2021/03/01 20:05] – created dgonzalez | aruba_networks:switch:4800:irf_configuration:error_the_device_is_not_in_the_current_irf [2021/03/10 16:20] (current) – removed dgonzalez | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====Problem Description : Error: The device is not in the current IRF ===== | ||
- | |||
- | |||
- | * **Product Model # : 4800G** | ||
- | |||
- | |||
- | * Software / Firmware version : 5.20 2202 | ||
- | |||
- | |||
- | * Fact : Attempting to add an IRF device to a stack, that was previously configured or misconfigured. | ||
- | |||
- | |||
- | 1.- Resetting the device back to factory defaults does not remove the IRF number | ||
- | |||
- | |||
- | | ||
- | |||
- | **ERROR: The device is not in the current IRF.** | ||
- | |||
- | | ||
- | Unable to add a new device to an IRF Stack | ||
- | |||
- | |||
- | Cause : If a device has been previously configured with an incorrect member ID or does not match the stack member ID, the new device will not synchronize with the existing stack. | ||
- | |||
- | |||
- | Fix : Use the following command to determine the current Member ID | ||
- | |||
- | |||
- | | ||
- | |||
- | |||
- | 4800G]dis irf conf | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | *4 | ||
- | | ||
- | | ||
- | |||
- | ---- | ||
- | |||
- | |||
- | |||
- | * indicates the device is the master. | ||
- | |||
- | |||
- | + indicates the device through which the user logs in. | ||
- | |||
- | |||
- | | ||
- | |||
- | |||
- | Undo irf member 4 renumber | ||
- | | ||
- | | ||
- | Undo irf member 4 irf-port 1 | ||
- | | ||
- | | ||
- | Undo irf member 4 irf-port 2 | ||
- | |||
- | |||
- | | ||
- | |||
- | |||
- | 4800G]dis irf conf | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | | ||
- | *4 | ||
- | | ||
- | | ||
- | |||
- | ---- | ||
- | |||
- | |||
- | * indicates the device is the master. | ||
- | |||
- | |||
- | + indicates the device through which the user logs in. | ||
- | |||
- | | ||
- | |||
- | Save | ||
- | | ||
- | | ||
- | Reboot | ||
- | |||
- | |||
- | | ||
- | |||
- | |||
- | Then issue the commands | ||
- | |||
- | |||
- | Irf member 1 renumber 3 | ||
- | | ||
- | | ||
- | Irf member 1 irf-port 1 port 1 | ||
- | | ||
- | | ||
- | Irf member 1 irf-port 2 port 2 | ||
- | | ||
- | Save | ||
- | | ||
- | | ||
- | Reboot | ||
- | |||
- | |||
- | Connect the new unit to the IRF Stack. | ||